- ページ 3
キーパッド Automatic Technology KPX-7V2のPDF クイック・セットアップ・マニュアルをオンラインで閲覧またはダウンロードできます。Automatic Technology KPX-7V2 4 ページ。 Wireless keypad
ページを印刷する
2. Adding / Deleting Users
2.1 Creating New User Pin's
B
efore creating new User Pins answer the following questions.
1. Does this User need access to all Channel functions (eg. Garage Door, Automatic Gate, Outside Lighting) or only one channel (eg.
2= Automatic Gate).
2. Is this User a Normal User with ongoing access or can I program a Temporary User in the KPX-7V2 Keypad and the User Pin will be
deleted after so many uses.
Once you have answered the above proceed to code the Keypad using the following steps;
a. Press the FCN button, followed by the Primary User Pin Code, then press the FCN button again.
b. Select the '1' button, followed by the FCN button.
c. Select a Memory (MEM) number between 2-20 and then press the FCN button.
NOTE: The Memory (MEM) number indicates the memory location of the PIN and is used to delete individual User Pin Codes as
required. Therefore it is important to record all information on the User Information Table (see over) .
d. If you wish to restrict the User to certain Channel functions, enter each channel they are permitted to access (eg. 2 = Automatic Gate,
3 = Outside Light) individually (press 2, pause, press 3, then press FCN button). If User is permitted to have access to all Channel
functions skip entering in the channel number and press the FCN button.
e. For Normal Users press FCN button and proceed to step f. For Temporary Users enter in the number of times the User Pin can be
accessed (1-99 uses) followed by the FCN button.
f. Enter in the new 4 digit User Pin and press FCN button.
g. Re-Enter the same 4 digit User Pin and press the FCN button.
h. The Keypad will beep and flash to indicate it is exiting the learning mode.
Short cut Guide - Creating New User
PRIMARY
FCN
FCN '1' FCN
USER
PIN
NOTE: To change the User Pin, simply enter the User Pin,
then follow step 1.2a - d in the Quick Set up Guide
2.2 Deleting User Pin's
a. Press the FCN button, followed by the Primary User Pin Code, then press the FCN button again.
b. Select the '2' button, followed by the FCN button.
c. Select the Memory (MEM) number of the User Pin and then press the FCN button.
NOTE: The Memory (MEM) number indicates the memory location of the PIN. Refer to the User Information Table (see over) for
Memory number.
d. Select the same Memory (MEM) number of the User Pin and then press the FCN button.
e. The Keypad will beep and flash to indicate it is exiting the learning mode.
f. Test the User Pin has been deleting by following step 1.3. The receiver should not respond.
Short cut Guide - Deleting User
PRIMARY
FCN
FCN '2' FCN
USER
PIN
2.3 Clearing the Memory
The KPX-7V2 Keypad contains a factory default pin. The factory default is 0000 and is used clear all memory and reload the factory
settings.
WARNING! Reloading the factory settings does not remove Channel information which has been coded into a
receiver and the receiver will continue to repsond to the KPX-7 Keypad.
If you set the KPX-7V2 back to factory default (0000) you will need reprogram the Primary User and all additional Users.
a. Press the FCN button, followed by the Primary User Pin Code, then press the FCN button again.
b. Select the '0' button, followed by the FCN button.
c. Enter in '0000' followed by the FCN button.
d. Re-enter in '0000' followed by the FCN button.
e. All memory is now cleared.
Short cut Guide - Clearing the Memory
FCN
CH#
CH#
FCN
MEM
1
2
(2-20)
FCN
MEM
(2-20)
PRIMARY
FCN
USER
FCN
FCN
# USES
NEW
NEW
(1-99)
PIN
PIN
FCN
MEM
FLASHES
(2-20)
BEEP
FCN '0' FCN
PIN
FCN
FLASHES
BEEP
FCN
FCN
'0000'
'0000'
FLASHES
BEEP