- ページ 4
カードリーダー HID iCLASS SE RKCLB40EのPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。HID iCLASS SE RKCLB40E 4 ページ。 Biometric reader
ページを印刷する
U S E R GU I D E
4.2.2 Manage Admins
This presents the choice of enrolling an Admin or verifying an existing
Admin card. Each option follows the standard Enrollment dialog
(see Section 2.3.1: Enrollment Dialog). The other choice is to revoke
an Admin. If this option is chosen the user must present an existing
Admin card to the reader. Users need to ensure they always have at
least one Admin card on the site as the only way to get a replacement
Admin card is to reset the reader to the factory setup and go through
the initial setup process.
4.2.3 Configuration Menu Functions
To access the Configuration menu, select 3 from the Administration
menu.
Note: The options in the Configuration menu will differ, depending on
how the Reader has been set up. For example, If the Reader has been
set up for iCLASS or iCLASS SR cards, then non-relevant menus (e.g.,
Site Key) will not be displayed.
Configuration
1. Language
2. Credential type
3. Mode
4. < more >
1.
Language: Changes the language.
2. Template Type: Changes the Template Type.
Notes:
If the user changes the Template Type from iCLASS cards
to Seos cards, then the user must exit the Administration
menu before enrolling Seos User or Admin credentials. After
exiting the administration menu the reader will prompt
the user to enter a Site Key for reader Seos operation. The
Site Key can then be set and an Admin card created which
matches the Site Key of the reader. Note: If the Template
Type is changed in this way, all readers on a site must be
reconfigured with the same Site Key.
If the user changes the Template Type from Seos cards to
iCLASS cards, then the Reader will reboot into Initial Setup
– Verify Admin mode. The confirmation Yes/No dialog will
display (because the Site Key is not required for iCLASS or
iCLASS SR cards).
3. Mode: Changes the Operational Mode.
4. Select 4 < more > to see the next page of Configuration options.
Second page of Configuration options
Configuration
1. PIN Required
2. BIO Required
3. Capture Quality
4. < more >
1.
PIN Required
Yes: To require a Local PIN Verify for access.
No: Does not require a PIN for access (Default).
Note: The PIN Required setting can only be changed from Yes
to No if the reader is ordered with the Local PIN Verify factory
configuration option. Also all cards on site may need to be re-
enrolled, because they may have been previously enrolled when
no Local PIN Verify was required. To facilitate this migration
process, It is suggested that the user sets up one or more
separate, dedicated enrollers that require a Local PIN Verify and
use these enrollers to add PINs to users' cards, including Admin
cards. The site Readers are set to ignore Local PIN Verify so
they will be able to accept the re-enrolled cards. Once all of the
user cards have been re-enrolled then the rest of the Readers on
the site can be reset to require Local PIN Verify.
Note: When a PIN is enrolled to iCLASS cards via the RKLB40
reader, this PIN can be used by both RKLB40 and R(P)K40
readers configured for Local PIN Verify.
hi d g l o b a l.com
iCLASS SE Biometric Reader
Note: When a PIN is enrolled to Seos cards via the RKLB40
reader, this PIN can only be used by RKLB40 readers configured
for Local PIN Verify. R(P)K40 readers configured for Local PIN
Verify can not read these card
2. BIO Required:
Yes: To require a fingerprint presentation for access (Default).
No: Does not require a fingerprint presentation for access.
Note: Seos Credentials require a fingerprint template enrolled
on the credential for configuration option BIO Required = No. A
fingerprint will not need to be presented for this option.
3. Capture Quality:
Low Quality: Only one scan is required when capturing each
fingerprint.
High Quality: Three scans are required when capturing each
fingerprint. This is the recommend mode as the likelihood
of success when a user presents a finger to gain access is
increased.
4. Select 4 < more > to see the next page of Configuration options.
Third page of Configuration options
Firmware: Displays the Firmware information, if needed,
when working with Technical Support.
1. Firmware
2. Visitor Card Enabled
4. < exit >
Note: Press # to bring up a page with the Site Key number.
The Site Key number page is only visible to Admins and is a
hidden option to prevent unintended display. The Site Key
number should be kept secure. (Option only appropriate
when the Template Type is set to Seos).
Visitor Card Enabled: This option is only available if the
Template Type is set to iCLASS.
Yes: To allow visitor cards to be used in this environment.
No: Do not allow visitor cards in this environment (Default).
If you select Yes and go to Manage Users there will now be a third
choice in the Enrollment dialog: Enroll Visitor. Visitor cards are
prepared ahead of time, are generic, and can be given to visitors
without requiring them to enroll their biometric information. No
fingerprint information will be processed by the reader. If PIN
Required (Local PIN Verify) is set, visitors will need to be told what
the Local PIN Verify PIN value is to permit access.
Select 4 < exit > to return to the first screen of Configuration
options.
4.3
Sensor Cleaning
For optimum performance, it is recommended that you clean the bio-
reader periodically. The use of a dry cloth is recommended to clean
the acquisition surface. In order not to scratch the surface, remove all
dust and residue with gentle movements.
CAUTION: Acidic liquids, alcohol or abrasive materials are prohibited.
4.4
Additional References
Documents kept up-to-date and available on-line:
iCLASS SE Biomectric Reader Advanced Use Case Application
www.hidglobal.com/PLT-03345
Note -
iCLASS SE Biometric / iCLASS SE Display Reader Installation
Guide -
www.hidglobal.com/PLT-02738
An ASSA ABLOY Group brand
RKLB40E; SRD Model: RKCLB40E
Configuration