- ページ 5

セキュリティセンサー ADEMCO 990のPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。ADEMCO 990 6 ページ。 Passive infrared motion detectors

ページを印刷する

LtD

ENABLE/DISABLE

The detector k shipped with the A&i

lt%

d&&i&d

(LED enabte/disaMe plug in pface). If desired, the LEO

may be enaked (after the Watk+Test' k axnplete) by

removing lhe LED enabfeMkabte pfug (see Fq. 3). To

prevent the fess of the plug, we suggest you instafl ff

onompinwhentheptugknotinuse.

If desired, the LED may be aktrofled from a remote

bcation, es fofiowsz

Remove the LED enabfe/diie

plug. Connect a

switched fine to the left-ftand pin (81) of tfte two

LEDpfnsrvhichcanbegroundedoropened(see

Fg.

4).

Grounding pin #I wffl diibfe the LED,

disconnedingRfrorngroundwiUenabkfheLE0.

Figure 4. Remote Control of LED

TEST PROCEDURES

Important: Two-minute warm-up ffme k required after

applying power. Testing should be amducted with the

protected area cleared of all people. L&arm tfte

fuotectfve system's control during the test procedure to

prevent repofting of unwanted afarms.

Walk-Test:

1. lheNarmLEDmustbeenafMatfhisfime&ED

enabkMkabk plug removed).

2 WIUI tront cover In ptace. want through fxotectfve

zones. observing tftat tfte detector's, LED figftts

whenevermofknkdetecfed.

The absofute range of ail

PIR

units k subject to

variation

because

*of different tyf~

of cfothing,

backgrounds

and ambient temperature. For (his

reason.ensure(hattftemosffRafyfntruderroufesare

well within Ihe PIRs protect&e zones and (hat walk-

testirlgkcarrkdoutabnglheseroutes.

After tfte Walk-lesr

k complete, tfte LED may be

disabled (LED enabMkabfe pfq fnsfafkd).

MAINTAINING PROPER OPERATION:

In order to maintain the detector fn.proper working

cpdiiontlkin~tthatIhe~ngbeobsenfed

Power should be provfded

at all tfmes. Loss of

powertotheunitwiffresufthtfteafanncontacfs

reverting to an afarm state. The units DC source

shoufdfx3vesfandbypoweravaifabfeforatfeast4

hours d operation during emergencies.

Unfts should never be re-afmed or relocated

without the advice or assktance of tfte alarm

selvicecompany.

physfcaf surroundings

tfm protected

area should not be changed. tf fumitum or sto&

k moved, or air-wndiii

or additionaf heating

k inslaued. lhe system may have to be readjusted

bythealarmseNiceoompany.

Walk-tests

ahoufd be Conducted hequentfy (at

least

weekly) to

confirm continued proper

awerage by each deNfor.

Tmubfo Z LED INOPERATfVE

Frobebte

Cauee8:

A. LED ena#a!dkabfe pfug k fnstaffad.

Reme@t Remove LED enabfeMkaMe pfug.

LED maffunction. Chedc for brokerMofted leads.

Return unit for service.

trouble

4~ DETECTION m

CUNWES

Probable Causes:

Repositioned

furniture or equipment

in the

protected area.

cautionalstomu

changes. Rst=

B. Mounting surface k unstable. A few degrees of

vertical shifl can change range subslantially.

RemsdL:

MolJnfonsecuNsuffaoe.

Troubfe Sz CONTROL

PANEL

INDICATES

CONTINUOUS FAULT IN ZONE OF

PROTECTION CONTAINING PIR..

(PIR'S ALARM LED NOT ur)

Probabb bum

loo many detectors being used fn the zone.

Each

detector adds 15 ofuns of aerfes resistance and Ihe

zone*s aDowable bop resktanoe k being exceeded.

Rem*

ReduoeuwnumborddactoNusedinthe

zoneuntfftfteserfesresk~kw&in~

affowafxfe kop resktanm permitted by the

wntrod.

TROUBLESHOOTING

l'roubte 1: INl'ERMITTE)ICI ALARM &ED

OPERATIVE)

Probable Causes:

Rapid temperature change. chedc for ete&iC Of

gas heaters, open ffames, ekctric arca. etc..

Verne@ Locate sour& and repositkn detector.

B. ~Z&YI.\

drapes, fight ffxtures. display

Remedjc

Efiminate source of motion.

Trouble 2: INTERMITTENT OR CONTlNUOUS

ALARM

Probabfe Causes:

DC voftage supplied to detector k inadequate,

fnterrnfttent. or pokttty revemed.

Remedy:

Ensure that proper polarity

and

adequate voffage k supplied and that

wiringkintact(noopensorsftorts)and

connecfiorls seam.

Protective kop k interrupted (open).

Determine whether interruption k in

protective foop wfring or at detector's

alarm relay contacts.

Disconnect

promtive bop aI detecbr relay contact

terminals and che& oontinuity across

terminals.

If absent at detector

terminals

(and proper voltage

supf&d to the detector). return unit for

sewice. it Present, check Protective

bopwiring.