キーパッド 2gig Technologies TS1のPDF インストレーション・インストラクションをオンラインで閲覧またはダウンロードできます。2gig Technologies TS1 2 ページ。 Touch screen wireless keypad
2gig Technologies TS1 にも: クイックマニュアル (5 ページ)
2GIG-TS1
Touch Screen
Wireless Keypad
For Remote Control of
the 2GIG Security System
Installation Instructions
WALL MOUNTING THE KEYPAD
USE THE THREE SCREWS AND
ANCHORS SUPPLIED TO ATTACH
THE MOUNTING PLATE TO THE WALL
ROUTE 18 AWG WIRE
BETWEEN THE KEYPAD
AND THE POWER SUPPLY
LOCATION
WIRE GAUGE CHART
GAUGE
MAXIMUM RUN
18
100 FEET
16
150 FEET
USE UN-SHIELDED 2-CONDUCTOR
INSTALL POWER SUPPLY
POWER
SUPPLY
POWER
SUPPLY
BRACKET
INSTALLED
FOR STANDARD
STYLE OUTLET
BRACKET
INSTALLED
FOR DECORA
STYLE OUTLET
PRODUCT DESCRIPTION
The Model 2GIG-TS1 Touch Screen Wireless Keypad is a remote control device
designed for the 2GIG security system Control Panel. The keypad supports all
operating and emergency functions of the system. The keypad is designed for
indoor use only.
The front panel
and
buttons serve as controls as well as indicators.
Pressing the
button displays emergency icons on the display for Panic, Fire,
and Emergency alarm activation (each has programmable options and can be
enabled or disabled). Pressing the
button changes the system display to the
Home Screen. The keypad is powered from a plug-in power supply (included).
The 2GIG-TS1 exchanges information through a secure 2-way wireless connection
with the Control Panel. Before operation the keypad must be "paired" with the
Control Panel. Refer to the Control Panel's installation instructions for details on
pairing the keypad to the Control Panel.
CONNECT POWER WIRES TO KEYPAD
RE-CONNECT THE
USE #6 INSULATED SPADE
HANGING STRAP
TERMINALS (NOT SUPPLIED)
TO CONNECT WIRES FROM
THE POWER SUPPLY TO
THE KEYPAD
OBSERVE
POLARITY !!!
PAIR KEYPAD WITH CONSOLE & TEST
PLACE THE CONSOLE IN
PROGRAMMING MODE
AND PREPARE IT FOR ENROLLING
THE WIRELESS KEYPAD
2GIG CONSOLE
REFER TO THE CONSOLE'S
INSTALLATION INSTRUCTIONS
FOR DETAILS ON PROGRAMMING
AND TESTING THE WIRELESS KEYPAD
WHEN LEARN IS PRESSED ON
THE CONSOLE, AND PAIR WITH PANEL
IS PRESSED ON THE TS1, THE TWO
TS1 WIRELESS
UNITS WILL COMMUNICATE AND
KEYPAD
AUTOMATICALLY ENROLL THE KEYPAD
KEYPAD PREPARATION
FLIP OPEN THE BACK COVER
LOOSEN CASE SCREW
2
1
OF THE KEYPAD
FOUR TURNS
THE BACK COVER IS USED
AS THE KEYPAD'S MOUNTING PLATE
3
DISCONNECT THE
HANGING STRAP
CLOSE KEYPAD
SNAP CASE CLOSED
TIGHTEN CASE SCREW
LIMITED WARRANTY
This 2gig Technologies Inc. product is warranted against defects in material
and workmanship for twelve (12) months. This warranty extends only to
wholesale customers who buy through 2gig Technologies Inc. authorized
distribution channels. 2gig Technologies Inc. does not warrant this product to
consumers. Consumers should inquire from their selling dealer as to the nature
of the dealer's warranty, if any. There are no obligations or liabilities on the
part of 2gig Technologies Inc. for consequential damages arising out of
or in connection with use or performance of this product or other indirect
damages with respect to loss of property, revenue, or profit, or cost of
removal, installation, or reinstallation. All implied warranties, including implied
warranties for merchantability and implied warranties for fitness, are valid only until
the warranty expires. This 2gig Technologies Inc. Warranty is in lieu of all other
warranties express or implied.
LOCATING THE KEYPAD
SELECT A LOCATION FOR THE KEYPAD,
BE SURE THAT AC POWER IS AVAILABLE NEARBY,
WATCH OUT FOR STUDS, ELECTRICAL, & PIPES IN THE WALL
USE THE KEYPAD'S BACK COVER AS A TEMPLATE
TO MARK THE THREE SCREW HOLES AND THE
POWER WIRING ACCESS HOLE
USE A DRYWALL SAW TO CUT THE WIRING HOLE
CONNECT POWER SUPPLY
POWER
SUPPLY
CONNECT POWER
WIRES TO THE
POWER SUPPLY
OBSERVE
RIGHT
PROPER
TERMINAL
POLARITY !!!
- 14 VDC
LEFT
TERMINAL
18 AWG / 2-CONDUCTOR
+ 14 VDC
TO KEYPAD
IMPORTANT !!!
Radio controls provide a reliable communications link and fill an important need
in portable wireless signaling. However, there are some limitations which must be
observed.
For U.S. installations only: The radios are required to comply with FCC Rules and
Regulations as Part 15 devices. As such, they have limited transmitter power and
therefore limited range.
A receiver cannot respond to more than one transmitted signal at a time and may be
blocked by radio signals that occur on or near their operating frequencies, regardless of
code settings.
Changes or modifications to the device may void FCC compliance.
Infrequently used radio links should be tested regularly to protect against undetected
interference or fault.
A general knowledge of radio and its vagaries should be gained prior to acting as a
wholesale distributor or dealer, and these facts should be communicated to the ultimate
users.
This device complies with FCC Part 15 and Canada Rules and Regulations.
Operation is subject to the following two conditions: (1) This device may not cause
harmful interference and (2) this device must accept any interference received,
including interference that may cause undesired operation.