アクセサリー ADEMCO 5890PIのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。ADEMCO 5890PI 2 ページ。 Passive infrared motion detector/transmitter

ページを印刷する

GENERAL INFORMATION

The

5890PI

Passive

Infrared

Detector/Transmitter

wireless device intended for use as part of a

5800 series wireless alarm system.

Designed for use in commercial and residential

installations, the 5890PI is a wall-mounted unit

with a standard lens that provides wide-angle

protection up to a range of 35 ft (10.6m). For

best coverage, mount the detector so that the

likely direction of intruder motion is across the

pattern.

When installed per the guidelines, the Split-

Zone Optics technology in the 5890PI provides

reasonable false alarm protection against pets

and other animals up to 40 lbs.

This document provides installation instructions

for the 5890PI, but the installer must be familiar

with the installation instructions for the 5800

Wireless Alarm System with which the 5890PI

is intended to be used.

FEATURES

• Split-Zone Optics provides pet immunity

against animals up to 40 lbs.

• Wireless operation for fast installation.

• Dual-element pyroelectric sensor provides

positive protection while minimizing false

alarms.

• Alternate-polarity pulse count option offers

greater stability in adverse environments.

• Provision to turn LED on while Walk Testing

(LED is turned off after testing).

• Tamper-protected

cover;

message if cover is removed.

• Wall or corner mounting options.

SYSTEM DESCRIPTION

Optical System

Uses efficiently designed Fresnel lenses with

Split-Zone Optics.

Radio Transmitter

The built-in transmitter serves only as the

communication link to the alarm system's

Receiver/Control, and can send alarm, tamper,

supervisory, and battery status messages to

the system's receiver/control. The transmitter is

not used for detection purposes. Each detector

has a unique ID code permanently assigned at

the factory. You must enroll this ID into the

control system at the time of installation. This

allows each detector used in the system to be

uniquely identified. You must program the

control to enroll the 5890PI as an "RF" type unit

(i.e., supervised RF).

conserve

battery

life

operation, no more than one transmission

sequence will occur within a 3-minute period.

There is no such time restriction in Test mode.

Alternate-Polarity Pulse Count

Two

jumper-selectable

detection

modes are provided: Instant response (Pulse

Count OFF) and Alternate-Polarity Pulse Count

(Pulse Count ON). With Pulse Count OFF, any

detected change in infrared energy triggers an

3$66,9(,1)5$5('027,21'(7(&72575$160,77(5

INSTALLATION INSTRUCTIONS

immediate

recommended when the detector is used to

Motion

monitor a narrow hallway where coverage is

battery-operated

provided by only a single zone. Use the Pulse

Count ON mode when the detector is installed

in areas where periodic changes in infrared

energy levels are normal (for example, where

forced-air heating ducts are present). In this

mode, at least two changes in infrared energy

must be detected within a short period before

an alarm is triggered.

Important

applications,

recommended.

SPECIFICATIONS

Pet Immune

Lens:

Pulse Count: Installer-selectable On/Off link.

Detectable

Walk Rate:

Mtg. Height: 7.0 ft recommended (2.1m),

Walk Test

Indicator:

Batteries:

unit

transmits

0perating

Temperature: 32°F – 122°F (0°C - 50°C).

Operating

Humidity:

Dimensions: 2-11/16"W x 5"H x 1-7/8"D

25'

(7.6m)

25'

(7.6m)

during

normal

7.5'

(2.3m)

response

Figure 1. Protection Pattern

alarm

signal.

This

mode

Note:

For

pet

immune

Pulse

Count

35 ft x 45 ft (10.6m x 13.7m).

30 zones (8 long, 7 over 7 inter-

mediate, 4 over 4 short-range).

0.5–10 ft/Sec (0.15–1.5m/Sec).

but may be mounted at other

heights (see Table 1).

Red LED with Test/Normal

(disable) link.

Two 3-volt Lithium batteries.

Use only ADEMCO No. 466,

Duracell DL123A, Panasonic

CR123A, Sanyo CR123A, or

Varta CR123A.

Up to 95% RH (max.), non-

condensing.

68mm x 127mm x 48mm.

ALTERNATE

COUNT POLARITY

EACH ZONE CONSISTS

OF 2 FIELDS

10'

20'

30'

35'

(3m)

(6m)

(9m)

(10.6m)

10'

20'

30'

35'

(3m)

(6m)

(10.6m)

(9m)

N5987-2V1 10/99 Rev. B

$'(0&23,

BATTERY INSTALLATION

1. Remove front cover by inserting a large

screwdriver blade (or small coin) in groove

between cover and base at the location

shown in Figure 2; rotate blade to override

snap fit, then lift cover off.

2. Observing correct polarity, install the two

Lithium batteries (supplied) into the battery

holders, as shown in Figure 5. Make sure

the batteries are firmly seated.

3. Replace the cover (snap fit).

Battery Caution

Risk of fire, explosion, and burns. Do not

recharge, disassemble, heat above 100°C, or

incinerate. Dispose of used batteries promptly.

Keep away from children.

Programming

Note:

programmed the detector's ID into the

system (i.e., this is an initial detector

installation), refer to the PROGRAMMING

section below and perform the ID enrolling

procedure before mounting or testing the

detector.

PROGRAMMING

You must enroll the detector's ID during

installation

the

system.

program the 5890PI as an "RF" type unit

(i.e.,

supervised

RF),

number as "1."

To program the detector, place the LED jumper

in the TEST position (see Figure 5), the Pulse

Count jumper in the OFF position, batteries

installed and cover on. Temporarily cover the

lens (a cloth will do) to prevent any activation

by the detector.

When prompted for the device's serial number,

you may either manually enter it or transmit

from the unit (remove the cloth cover and

motion your hand over the lens to activate the

detector, press the tamper switch, etc.). Refer

to the control panel installation instructions for

programming details.

Return LED jumper to the NORMAL position

after it is enrolled in the control.

INSTALLATION

Installation Hints

• Do not install where the detector is exposed

to direct sunlight or directly above strong

sources of heat.

• Make sure the detection area does not have

obstructions (curtains, screens, large pieces

of furniture, plants, etc.) that may block the

pattern of coverage.

• Avoid locating a unit in areas that contain

objects likely to produce a rapid change in

temperature,

such

radiators, or ducts (or heaters of any kind),

air conditioners, open flame, etc.

• Do not mount on an unstable surface.

IMPORTANT: For installation with pets, be

sure to follow the guidelines described in

Table 2.

you

have not

You

should

and

the

"Loop"

central

heating,