- ページ 2

エンジン Dynamite Mach 15RのPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Dynamite Mach 15R 2 ページ。

ページを印刷する

7527_DYN_mach15RE_man#88EE5.pdf

Idle Stop Adjustment

The last setting to be made is the idle stop screw. Turning

this screw clockwise increases the idle speed; whereas

turning the screw counterclockwise will make the engine

idle at a lower speed. Ideally, the engine should idle just

fast enough to be reliable in acceleration and transition

from idle to full speed. Avoid an idle speed that is too

fast, as it will cause damage to your clutch.

Engine Maintenance

Periodic maintenance must be performed in order

to keep your engine in proper operating condition. After

each day of running, it' s critical to use high quality after-

run oil to protect the internals of the engine and protect

them against corrosion. The methanol used in the fuel

attracts moisture that can cause corrosion (particularly in

the ball bearings). We recommend Blue Thunder™ Final

Run (DYN2255) as it' s specifically formulated to protect

your engine between uses. Follow these steps after

running your engine:

1) Empty all fuel from the tank and fuel lines

2) Use Final Run fuel following the instructions on

the container

3) Clean and inspect the engine, air cleaner and

fuel system

Troubleshooting Guide

Possible Cause/Solution

Problem

• Reset needles to the

Engine won't start

CMY

factory setting

• Incorrect needle settings

• Out of fuel/old, bad or

improper fuel

• Clogged fuel line

• Bad or improper glow plug

• Glow igniter not charged

• Engine flooded

• Pressure line blocked or

Engine starts, then dies

disconnected

• Bad glow plug

• High-speed needle too lean

• Hole or tear in fuel line

• Bad glow plug idle speed set

Engine starts and runs

too low

for

⁄

tank, then quits

• Overheated engine

(too lean)

• Improper needle settings

12/8/04

2:54:42 AM

Spare Part Listing

LOSR6535 Complete Pull Starter: Mach 15RE

LOSR6536 PS Backplate: Mach 15RE

LOSR6537 PS One-way Bearing: Mach 15RE

LOSR6538 PS Shaft: Mach 15RE

LOSR6539 PS Cushion Spring Mach 15RE

LOSR6540 PS Screw Set: Mach 15RE

LOSR6541 PS Handle Set: Mach 15RE

LOSR6542 PS Recoil Spring: Mach 15RE

LOSR6543 PS Rope & Pulley: Mach 15RE

LOSR6548 Carb Retainer Post & Nut: Mach 15RE

LOSR6552 Throttle Barrel: Mach 15RE

LOSR6553 Throttle Barrel Boot: Mach 15RE

LOSR6554 Throtle Arm W/ Nut: Mach 15RE

LOSR6555 High Speed Needle Valve: Mach 15RE

LOSR6556 High Speed Needle Holder: Mach 15RE

LOSR6557 High Speed Assembly Washers: Mach 15RE

LOSR6558 Fuel Inlet Nipple: Mach 15RE

LOSR6559 Low Speed Needle Valve: Mach 15RE

LOSR6564 Rotary Carburetor: Mach 15RE

LOSR6565 Complete O-Ring Set: Mach 15RE

LOSR6580 Cylinder Head: Mach 15RE

LOSR6581 Combustion Head Button: Mach 15RE

LOSR6582 Head Shim .1mm: Mach 15RE

LOSR6583 Head Shim .2mm: Mach 15RE

LOSR6584 Piston/Sleeve: Mach 15RE

LOSR6585 Wrist Pin: Mach: 15RE

LOSR6586 Wrist Pin Clips: 15RE

LOSR6587 Connecting Rod: Mach 15RE

LOSR6588 Front Bearing: Mach 15RE

LOSR6589 Collet: Mach 15RE

LOSR6590 Crankcase: Mach 15RE

LOSR6591 Header Seal: Mach 15RE

LOSR6592 Rear Bearing: Mach 15RE

LOSR6593 P/S SG Crankshaft: Mach 15RE

LOSR6594 Idle Screw: Mach 15RE

LOSR6595 O Ring Set: Mach 15RE

Warranty

Mach 15 RE engines are guaranteed against original

defects in materials and workmanship for a period of

90 days from date of purchase. Mach 15 engines are of

excellent quality and designed to provide many hours

of racing enjoyment. If cared for properly, these engines

are extremely durable. However, normal "common sense"

care must be given to your engine in order to maximize

its performance and service life. The following

conditions/problems cannot be covered under warranty:

• Recoil starter

•Damage due to lack of maintenence

• Rusted bearings

• Crash-related damage (over-revving, runaways,

free-wheeling, etc.)

• Damage due to use of improper fuel or glow plugs

• Damage due to lean runs (seized connecting rods,

pistons, etc.)

• Damage caused by dirt or foreign objects being

ingested into the engine

• Damaged from improper disassembly or reassembly

• Modification of any kind

• Normal engine wear

Should you need to send your engine in for warranty or

non-warranty repairs, please follow these steps:

1) Ship your engine (in its original box) packed

inside a sturdy box, freight prepaid to:

Horizon Service Center

ATTN: MACH 15 RE Service

4105 Fieldstone Rd.

Champaign, IL 61822

2) Include a note containing a brief summary of the

problems you are experiencing with your MACH

.15 RE engine. Please tell us:

• Nitro content and brand of fuel used in

the engine

• Type of glow plug used

• Type of air cleaner used

• Approximate running time on the engine

prior to difficulties developing

Date your correspondence and include your return

shipping address, as well as a daytime telephone

number and e-mail address (if applicable).

3) Warranty Repair

If you believe that the problem(s) with your

engine are covered under warranty, you must

include your original dated sales receipt to verify

proof of purchase date. Providing the conditions

of warranty have been met, your engine will be

repaired without charge.

4) Non-Warranty Service

Should your repair costs exceed $50.00, you'll be

provided with an estimate advising you of your

options. Any charges for return shipping of non-

warranty repairs will be billed to you.

5) Payment Method

Please advise the Horizon Service Center

of the method of payment you prefer to use.

The Service Center accepts Visa or Master Card.

When using credit cards, please include your

card number, expiration date and the name

as it appears on the card.

Mach 15 engines are manufactured in Taiwan and

distributed worldwide by

Horizon Hobby, Inc.

4105 Fieldstone Rd.

Champaign, IL 61822

www.horizonhobby.com

7527