- ページ 2
アンプ Hifonics TPS-A350.4のPDF クイック・スタート・インストール・マニュアルをオンラインで閲覧またはダウンロードできます。Hifonics TPS-A350.4 2 ページ。
ページを印刷する
Setup
A
The illustrations below describe the various controls. Refer to
the illustration that matches your amplifier.
Settings
TPS-A500.1
BOOST
L
0dB
12dB
1
GAIN Adjustment
INPUT
INPUT
GAIN
LPF
SUBSONIC
R
The gain control purpose is to match
MIN
MAX
50Hz
150Hz
15Hz
50Hz
the output of your source signal to the
amplifier. Refer to the section B below for
detailed instructions.
TPS-A500.2
2
X-OVER Switch
X-OVER
This switch will set the amplifier to have
L
BPF
HPF
a full frequency output or to filter out high
INPUT
INPUT
GAIN
LPF
HPF
HPF
or low frequencies. The NA1-400.2 offers
R
either a bandpass or a high pass filter.
MIN
MAX
50Hz
300Hz
15Hz
300Hz
3
Frequencies Adjustment
The Low Pass Filter will cut off the
TPS-A350.4
frequencies above the setting. The High
Pass Filter will cut off the frequencies
INPUT
FRONT
REAR
X-OVER
X-OVER
below the setting.
L
L
L
HPF
FULL
HPF
FULL
FRONT
REAR
FRONT
4
SUBSONIC Adjustment
F GAIN
R GAIN
R
R
R
The Subsonic Filter will cut off the
MIN
MAX
MIN
MAX
frequencies below the setting. If using
with a subwoofer the settin should be kept
between 15-25Hz.
TPS-A600.5
5
BOOST Switch
The Boost Switch will increase the signal
12dB at 45Hz. Be aware this setting can
cause distortion if the gain is not set
properly.
B
This is a critical step to insure your amplifier
is properly adjusted to match the signal
output level of your source unit.
Level Setting
THIS IS NOT A VOLUME CONTROL!
R
R
1.
If possible, with the source unit off, confirm that the primary volume control is
INPUT
FRONT
turned down (counter clockwise).
2.
Turn on the source unit (CD, or MP3 player). Re-confirm that the volume is
L
L
turned down. Make sure the source unit controls; balance, fader, bass and
treble are all set to center or "0" adjustment. Make sure that the green LED on
the end of the amplifier is illuminated.
3.
Play a clean musical selection of which you are very familiar. CD is preferred.
Do not use radio signals for level setting. Hit play and start turning the volume
of the source unit up.
4.
Stop increasing the source unit volume when you reach 3/4 (about 75%) or until
you hear speakers begin to slightly start producing distortion.
5.
Increase the amplifier gain (clockwise) until distortion is heard, then back
the level down (counter clockwise) until the distortion is eliminated. Small
adjustments may need to be made to balance the levels of multiple amplifiers.
5
BOOST
L
0dB
12dB
LEVEL
LPF
SUBSONIC
R
9V 0.2V
50Hz 150Hz
15Hz 50Hz
1
3
4
2
X-OVER
L
HP OFF LP
LEVEL
HP
LP
R
9V 0.2V
15Hz 300Hz 50Hz 300Hz
1
3
3
2
FRONT
REAR
X-OVER
X-OVER
L
HP
OFF
HP
OFF
REAR
LEVEL
LEVEL
R
9V
0.2V
9V
0.2V
1
1
3
4
5
1
2
1
2
Visit Hifonics.com
GAIN
LPF
SUBSONIC
The information contained within this document is intended to offer some basic guidelines
MIN
MAX
50Hz
150Hz
15Hz
50Hz
for a few of the most common installations. More complex audio systems should be
R
installed by a competent professional. Additional installation information available at
SUBSONIC
REAR
Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from
15Hz
300Hz
L
defects in material and workmanship for a period of one (1) year from the date of purchase.
X-OVER
BOOST
Maxxsonics USA Inc. will, at it's discretion, repair or replace defective products during the warranty
period. Components that prove to be defective in materials and workmanship under proper installation
and use must be returned to the original authorized Maxxsonics USA Inc. retailer from where it was
LPF
FULL
0dB
12dB
purchased. A photocopy of the original receipt must accompany the product being returned. The
costs associated with removal, re-installation and freight are not the responsibility of Maxxsonics
USA Inc. This warranty is limited to defective parts and specifically excludes any incidental or
consequential damages connected therewith. To view the full warranty, please visit the website.
FRONT
REAR
GAIN
GAIN
MIN
MAX
MIN
MAX
www.maxxsonics.com
WARRANTY
FRONT
REAR
X-OVER
X-OVER
HPF
FULL
HPF
FULL
Hifonics products are designed and engineered in the USA by
www.maxxsonics.com
Installation Guide
TPS-A500.2
TPS-A350.4
TPS-A500.1
TPS-A600.5
Congratulations on your choice of a Hifonics amplifier.
This "Quick Start Installation" guide is meant to help you
"hook up" and play music. For more detailed information,
on system setting, speaker and subwoofer configuration
and full specifications by model visit the website,
http://hifonics.com/manuals.html
HF TPS-A QSG 01 - rev1