- ページ 7
アンプ Hifonics XXV-ColossusのPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Hifonics XXV-Colossus 20 ページ。 Xxv edition high performance amplifier
ページを印刷する
FULL RANGE STEREO
This is the most basic application for the XXV Series 2 channel amplifiers.
1. Interconnect cable checklist:
Connect the LINE INPUTS to the Radio/CD with good quality RCA cables.
2. Crossover Switch:
The X-OVER switch must be in the FULL position.
3. Crossover frequency control checklist:
N/A for full range operation.
FULL RANGE
STEREO LINE INPUT
FULL RANGE MONO
This application illustrates the basic mono bridging method for all HiFonics
amplifiers.
Interconnect cable checklist:
A MONO signal source is required, such as would be available from the mono
sub bass output of an active crossover, whether standalone, or built into a head
Important:
unit or equalizer.
Do not be tempted to connect the hot, or positive
outputs, from any source together to obtain a mono signal, as this could very
well damage the output stage of that source.
It is necessary to feed the SAME signal to both left and right inputs via a
Y-adapter RCA cable.
Connect the mono speaker positive terminal to the LEFT +, and its negative
terminal to RIGHT -.
FULL RANGE
MONO LINE INPUT
VIA Y-ADAPTER
FROM MONO SOURCE
XXV JUNO 2 CHANNEL AMPLIFIER APPLICATIONS
PARAMETRIC EQ
BALANCED
PHASE
CUT/BOOST
LEFT
INPUT
LEVEL
LEFT
RIGHT
0dB
BANDWIDTH
FREQ
9V
0.2V
0
180
0
180
-10 +10dB
40 400Hz
X1 X10
MO ST
FULL RANGE
RIGHT
OUTPUT / INPUT
15
150Hz
40 400Hz
LP/BP
LP/BP HP
HFR-G1
SUBSONIC
FREQ
CROSSOVER
REMOTE
-6dB
XXVR-1
DIAGNOSTICS
GREEN: POWER
AMBER: THERMAL
-20dB
0dB
RED: SHORT
BASS REMOTE
PARAMETRIC EQ
BALANCED
PHASE
CUT/BOOST
LEFT
INPUT
LEVEL
LEFT
RIGHT
0dB
BANDWIDTH
FREQ
9V
0.2V
0
180
0
180
-10 +10dB
40 400Hz
X1 X10
MO ST
FULL RANGE
RIGHT
OUTPUT / INPUT
15
150Hz
40 400Hz
LP/BP
LP/BP HP
HFR-G1
SUBSONIC
FREQ
CROSSOVER
REMOTE
-6dB
DIAGNOSTICS
GREEN: POWER
AMBER: THERMAL
-20dB
0dB
RED: SHORT
BASS REMOTE
4. Line Level:
Refer to the section "Setting up systems after installation for best performance"
5. Bass Remote Module:
Plug in the Bass Remote Module to the amplifier "REMOTE" jack.
NOTE: Minimum final loudspeaker impedances:
4 & 2 Ohms stereo, 4 Ohms mono
Caution: This amplifier is not capable of 1 Ohms stereo or 2 Ohms bridged.
FUSE
RED - CLIP
AMBER - NEAR CLIP
GREEN - PRE-CLIP
SPEAKER OUTPUT
BRIDGED
+
L-CH
-
+
R-CH
-
X1 X10
DIAGNOSTICS
RED - SHORT CIRCUIT
AMBER - THERMAL
CLIP
FULL RANGE
GREEN: PRE-CLIP
AMBER: SOFT CLIP
RED: HARD CLIP
SPEAKERS
Switch setting checklist:
The AMPLIFIER X-OVER switch must be in the FULL position.
Crossover frequency control setting checklist:
N/A for full range operation.
TIP:
If you are using the mono sub bass output of an active crossover, there is
nothing wrong with switching in the low pass filter in these amplifiers for a
steeper low pass roll-off.
Caution: This amplifier is not capable of 1 Ohms stereo or 2 Ohms bridged.
FUSE
RED - CLIP
AMBER - NEAR CLIP
GREEN - PRE-CLIP
SPEAKER OUTPUT
BRIDGED
+
-
+
-
L-CH
R-CH
X1 X10
DIAGNOSTICS
RED - SHORT CIRCUIT
AMBER - THERMAL
XXVR-1
CLIP
GREEN: PRE-CLIP
AMBER: SOFT CLIP
RED: HARD CLIP
FULL RANGE
MONO SPEAKER
+12V
REM
GND
POWER INPUT
CHASSIS GROUND
REMOTE TURN-ON
TO BATTERY + 12v VIA FUSE
+12V
REM
GND
POWER INPUT
CHASSIS GROUND
REMOTE TURN-ON
TO BATTERY + 12v VIA FUSE
5