- ページ 6
温度コントローラー Autonics TC4SPのPDF マニュアルをオンラインで閲覧またはダウンロードできます。Autonics TC4SP 14 ページ。 Touch switch type temperature controller
Autonics TC4SP にも： マニュアル (14 ページ), マニュアル (2 ページ), 取扱説明書 (2 ページ), クイック・スタート・マニュアル (9 ページ), クイック・スタート・マニュアル (10 ページ)
ページを印刷する
Parameter Group
①
Press any key among
,
,
,
SV setting
※ 1: It is not displayed for AC/DC power model (TC4 - 2R).
※ If no key entered for 30 sec., it returns to RUN mode automatically and the set value of
parameter is not be saved.
※
This parameter might not be displayed depending on other parameter settings.
① Press any key once in RUN mode, it advances to set value setting group.
② Press
key over 2sec. in RUN mode, it advances to parameter group 1.
③ Press
key over 4sec. in RUN mode, it advances to parameter group 2.
④ First parameter will be displayed on viewer when it advances to the setting group.
⑤ Press
key over 3sec. in the setting group, it returns to RUN mode.
※ Exception: Press
key once in SV setting group it returns to RUN mode.
※ Press
key again within a sec after return to RUN mode by press
3sec., it advances to the first parameter of previous setting group.
※ Parameter setup
Parameter group 2 → Parameter group 1 →
• Set parameter as the above considering parameter relation of each setting group.
• Check parameter set value after change parameter of setting group 2.
※ Indicator model (TC4 -N N)displays shaded parameter (
※Alarmoperationmode[ AL-1 , AL-2 ] parameter of parameter group 2 is decided whether to display according by alarm output type.
※ If alarm operation mode [ AL-1 , AL-2 ] of parameter group 2 is set to AM)_ / SBa
Run mode
②
2 sec.
Parameter group 1
PAR1
[
3 sec.
④
AL1
AL1 alarm temperature
AL2
AL2 alarm temperature
AT
Auto tuning
P
Proportional band
I
Integral time
D
Derivative time
Manual reset
RSET
(Normal deviation correction)
HYS
ON/OFF control hysteresis
SV setting
) of parameter group 2.
Economical PID Control
Parameter 2group
]
IN-T
Input type
UNIT
Temperature unit
IN-B
Input correction
MAvF
Input digital filter
L-SV
SV low-limit value
H-SV
SV high-limit value
O-FT
Control output operation
C-MD
Control type
OUT
Control output
SSrM
SSR drive output method
T
Control cycle
AL-1
AL1 alarm operation mode
AL-2
AL2 alarm operation mode
AHYS
Alarm output hysteresis
LBaT
LBA monitoring time
LBaB
LBA detection range
DI-K
Digital input key
Control output MV in case of
ErMV
input break error
key over
LOC
Parameter lock
/ LBa , AHYS parameter is not displayed.
⑤
③
4 sec.
PAR2
[
]
3 sec.
※1
H-59
(A)
Photoelectric
Sensors
(B)
Fiber
Optic
Sensors
(C)
Door/Area
Sensors
(D)
Proximity
Sensors
(E)
Pressure
Sensors
(F)
Rotary
Encoders
(G)
Connectors/
Sockets
(H)
Temperature
Controllers
(I)
SSRs / Power
Controllers
(J)
Counters
(K)
Timers
(L)
Panel
Meters
(M)
Tacho /
Speed / Pulse
Meters
(N)
Display
Units
(O)
Sensor
Controllers
(P)
Switching
Mode Power
Supplies
(Q)
Stepper Motors
& Drivers
& Controllers
(R)
Graphic/
Logic
Panels
(S)
Field
Network
Devices
(T)
Software