- ページ 11

芝刈り機 909 50620のPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。909 50620 19 ページ。 139cc 4 stroke petrol lawn mower

ページを印刷する

Adding and checking the oil

Adding and Checking the oil

IMPORTANT: The motor of this mower is packed with NO OIL in the motor.

Prior to starting the motor, Oil MUST be added to the sump of the motor.

Failure to add sufficient oil will result in damage to the motor which is NOT

covered under the warranty of the mower.

On a new mower, the motor needs to be filled with 600ml of SAE 10W/30

engine oil.

Each time the mower is used, the oil level should be checked and if low, add

sufficient oil to ensure the oil level is to the full mark on the oil dipstick (17).

1. Position the lawn mower on a flat and level surface. Clean the area directly

around the oil filler cap (17).

2. Remove the oil filler cap (17) by unscrewing it in an anti-clockwise direction

approximately 4 turns, and lift the cap outwards (Fig L).

Clean the oil dipstick (17) with a clean cloth, cleaning away any visual oil.

NOTE: The cap is a full threaded fit.

3. FOR A NEW MOWER, add 600ml of SAE 10W/30 engine oil. Before replacing

the dip stick / filler cap, allow a minute or so to allow the oil in the filler tube

to fully drain of oil.

4. For both a new mower and also a previously used mower, measure the

amount of oil in the motor by re-inserting the oil dipstick back on top of

the filler tube, BUT DO NOT screw the cap in place.

5. After a few seconds, remove and inspect the oil level on the bottom of the

oil dipstick (17). (Fig M)

6. The oil level should be between the low and maximum marked section of

the oil dipstick (17) (Fig N). If the oil level is sufficient replace the oil cap by

inserting and screwing back in the oil filler tube in a clockwise direction

until firm.

7. If the oil level is insufficient, ie the oil level is not on the marked section of

the oil dipstick (17), add further oil in 50ml intervals and repeat steps 4, 5, 6,

and 7 until the correct oil level is obtained.

Always ensure the oil filler cap (17) is firmly locked in place before the

motor is started. Do not over fill with oil above the maximum mark.

Only use SAE 10W/30 engine oil.

LOOSEN

TIGHTEN

e-mail: [email protected]

MODEL: №. 50620

139cc 4 Stroke Petrol Lawn Mower

CORRECT

LEVEL

HIGH

LOW

AFTER SALES SUPPORT

1800 909 909

(toll free)

139cc 4 Stroke Petrol Lawn Mower

Fuelling

WARNING: Do not refill fuel tank while

engine is running or is hot. Ensure the motor is switched off before

undertaking this task.

IMPORTANT: Fuel goes off after about 3-4 months.

If you find your mower does not start, first change

the fuel in the fuel tank (14) with newly purchased

fuel and open the fuel bowl drain (23) for

approximately 5 seconds to drain out any old fuel

from the motor.

1. To open the fuel drain screw (23), turn the drain

screw in an anti clockwise and remove the screw

(Fig O). Fuel should drain from the bottom of

the bowl.

2. To re seal the fuel drain screw (23), replace the

screw and rotate the drain screw in a clockwise

direction until firm and the discharge stops.

• Be careful not to admit dust, dirt, water or other

foreign objects into the fuel.

• Wipe off spilt fuel thoroughly before

starting engine.

• Ensure you DO NOT put fuel in the lawn mower in close proximity to any

open flames, lit cigarettes, or hot objects.

NOTE: Do not use ethanol based fuel. Use fresh unleaded fuel.

1. Unscrew the fuel tank cap (15) in an anti-clockwise direction, and pour

fresh unleaded fuel into the fuel tank (14) with the aid of a funnel. (Fig P)

2. Fill the tank to approximately 2.5 cm below the lowest portion of the neck

to allow for fuel expansion. Be careful not to over fill.

3. Be careful not to spill any petrol. If this happens, wipe the spill with a

clean rag.

4. Start the engine at least 3 metres away from the area where the fuel tank

(14) has been filled in order to avoid the risk of fire.

WARNING: Never attempt to refuel the engine while it is running

or still warm, allow it to cool before fuelling.