タイマー Autonics CT SeriesのPDF 製品マニュアルをオンラインで閲覧またはダウンロードできます。Autonics CT Series 11 ページ。 Programmable digital counters / timers
Autonics CT Series にも: マニュアル (4 ページ), マニュアル (13 ページ)
TCD220014AA
Programmable Digital
Counters / Timers
CT Series
PRODUCT MANUAL
For your safety, read and follow the considerations written in the instruction
manual, other manuals and Autonics website.
The specifications, dimensions, etc. are subject to change without notice for product
improvement. Some models may be discontinued without notice.
Features
• Communication function supported (communication model): RS485 (Modbus RTU)
• One-shot output time setting range: 0.01 sec to 99.99 sec by setting per 10ms
[Counter]
• Prescale value setting range: 6-digit model: 0.00001 to 99999.9 /
• Various input / output modes (9 input /11 output modes)
• BATCH counter, count Start Point (counting initial value) setting function
[Timer]
• Various output modes (13 modes)
• Various time setting range: 6-digit model: 0.001 sec to 99999.9 hour /
• '0' time setting function
• Selectable timer memory retention function for indicator model.
ᜢ ᜧ ᜫ
Find Quality Products Online at:
4-digit model: 0.001 to 999.9
4-digit model: 0.001 sec to 9999 hour
GlobalTestSupply
www.
Safety Considerations
• Observe all 'Safety Considerations' for safe and proper operation to avoid hazards.
• symbol indicates caution due to special circumstances in which hazards may occur.
Warning
Failure to follow instructions may result in serious injury or death.
01. Fail-safe device must be installed when using the unit with machinery that
may cause serious injury or substantial economic loss. (e.g. nuclear power
control, medical equipment, ships, vehicles, railways, aircraft, combustion
apparatus, safety equipment, crime / disaster prevention devices, etc.)
Failure to follow this instruction may result in personal injury, economic loss or fire.
02. Do not use the unit in the place where flammable / explosive / corrosive gas,
humidity, direct sunlight, radiant heat, vibration, impact, or salinity may be
present.
Failure to follow this instruction may result in explosion or fire.
03. Install on a device panel to use.
Failure to follow this instruction may result in fire or electric shock.
04. Do not connect, repair, or inspect the unit while connected to a power
source.
Failure to follow this instruction may result in fire or electric shock.
05. Check 'Connections' before wiring.
Failure to follow this instruction may result in fire.
06. Do not disassemble or modify the unit.
Failure to follow this instruction may result in fire or electric shock.
Caution
Failure to follow instructions may result in injury or product damage.
01. When connecting the power / sensor input, relay output and communication,
use AWG 20 (0.50 mm
) cable or over, and tighten the terminal screw with a
2
tightening torque of 0.74 to 0.90 N m.
Failure to follow this instruction may result in fire or malfunction due to contact
failure.
02. Use the unit within the rated specifications.
Failure to follow this instruction may result in fire or product damage.
03. Use a dry cloth to clean the unit, and do not use water or organic solvent.
Failure to follow this instruction may result in fire or electric shock.
04. Keep the product away from metal chip, dust, and wire residue which flow
into the unit.
Failure to follow this instruction may result in fire or product damage.
Cautions during Use
• Follow instructions in 'Cautions during Use' .
Otherwise, it may cause unexpected accidents.
• Power supply should be insulated and limited voltage / current or Class 2, SELV power
supply device.
• Use the product, 0.1 sec after supplying power.
• When supplying or turning off the power, use a switch or etc. to avoid chattering.
• Install a power switch or circuit breaker in the easily accessible place for supplying or
disconnecting the power.
• When the counter is operating, in case of contact input, set count speed to low
speed mode (1 cps or 30 cps) to operate. If set to high speed mode (1 k, 5 k, 10 kcps),
counting error occurs due to chattering.
• Use twisted pair wire for communication line.
• Keep away from high voltage lines or power lines to prevent inductive noise.
In case installing power line and input signal line closely, use line filter or varistor at
power line and shielded wire at input signal line.
Do not use near the equipment which generates strong magnetic force or high
frequency noise.
• This unit may be used in the following environments.
- Indoors (in the environment condition rated in 'Specifications')
- Altitude max. 2,000 m
- Pollution degree 2
- Installation category II
.com