- ページ 2

ミュージックペダル Galaxy Industries GLX Noise GateのPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Galaxy Industries GLX Noise Gate 2 ページ。

ページを印刷する

NG-100 NOISE GATE

INSTRUCTIONS

Thanks for purchasing our product. In order to make the best use of your

NG-100, please read the following carefully.

FEATURES

The NG-100 is a special pedal to get rid of the unwanted noise. Set the SENS

knob for dynamic performance. The NG-100 can be used as a string sound

simulator by setting the ATTACK and DECAY knob.

BATTERY REPLACEMENT

1. Loosen the screw on the pedal to

open it.

2. Remove the battery from the

battery compartment and

disconnect the battery cable.

3. Connect a new battery to the

battery cable and put it back

in the battery compartment.

Make sure that the polarity

of the battery is correct and the

battery cable does not interfere with

the spring or pedal cover.

4. Push the coil spring into the spring

base and close the pedal.

5. Insert the thumb screw into the guide bush hole and ﬁrmly tighten the

screw.

IMPORTANT NOTES

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Do not use this apparatus near water.

5. Clean only with dry cloth.

6. Do not block any ventilation openings. Install in accordance with the

manufacturer's instructions.

7. Do not install near any heat sources such as radiators, heat registers,

stoves or any other apparatus (including ampliﬁers) that create heat.

8. WARNING: to reduce the risk of ﬁre or electric shock, do not expose this

apparatus to rain or moisture.

9. Protect the power cord from being walked on or being pinched.

10. Unplug this apparatus when unused for long periods of time.

11. There are no user serviceable parts inside. All servicing has to be done by

qualiﬁed service personnel. Servicing is required when the apparatus has

been damaged in any way, such as when the power supply cord or plug

is damaged, when liquid has been spilled or objects have fallen into the

apparatus, when the apparatus has been exposed to rain or moisture, when

the apparatus does not operate normally or when it has been dropped.

OWNER'S MANUAL

PANEL DESCRIPTION

1. AC Adaptor Jack: Connect an AC adaptor (100-140V/50-60Hz).

An AC adaptor allows long and secure operation without worrying about

battery life.

Use the proper supply for your area's Mains line voltage.

2. Indicator LED: This LED indicates when the effect is turned on.

•

Operating on battery power only: when the LED becomes dim or does

not light the battery needs to be replaced.

3. Level Knob: Use this control to adjust the output level of the NG-100.

4. Attack Knob: Use this control to adjust the time needed for the sound to

be boosted when the input signal becomes higher than the set threshold

level.

5. Decay Knob: Use this control to adjust the compression ratio of the limiter.

6. Sens Knob: Use this control to adjust the threshold level where the noise

gate starts working.

7. Output Jack: Use the jack to connect an ampliﬁer or other units.

8. Pedal: Press the pedal to turn the effect on and off.

9. Thumb Screw: Loosen the screw to open the pedal for battery

replacement. (For details of the battery replacement, see "BATTERY

REPLACEMENT")

10. Input Jack: Connect your instrument to this jack. To prolong battery life,

disconnect all cables from the pedal when it's not in use.

SPECIFICATIONS

Input Impedance

1MΩ

Output Impedance

1kΩ

Recommended Load

Impedance

10kΩ or greater

Residual Noise

-110Bu (IHF-A, Typ.)

Power Supply

DC 9V; Dry Battery (6F22/9V), AC adaptor

Connections

Input, Output, AC Adaptor

Controls

Pedal Switch, Level, Attack, Decay, Sens

Indicator

Check indicator (serves also as battery check indicator)

Current Draw

8mA, (DC 9V)

Dimensions

72*128*60 mm.

Weight

390g (no battery)

Option

AC adaptor

CONNECTIONS

1. Connecting an instrument to this jack will automatically switch the unit on.

Be sure to disconnect the cord from this jack when the unit is not being

used.

2. Before connecting or disconnecting any instrument, make sure that the

volume of the ampliﬁer is turned down.

3. The output jack is to connect an ampliﬁer or other units for mono use.

Both the dry and processed signals are output.