- ページ 11

リモートスターター Autopage C3-RS-601のPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Autopage C3-RS-601 19 ページ。 Remote car starter
Autopage C3-RS-601 にも: クイック・スタート・インストール・マニュアル (2 ページ)

A. PROGRAMMING TRANSMITTER:
Note: This remote start system will only retain the last 4 remote transmitters programmed. If the transmitter memory is
exceeded, the security system will start deleting transmitters from memory in chronological order.
PROGRAMMING THE REMOTE TRANSMITTER
1. Turn the Ignition 'switch 'OFF/ON' 3 TIMES and stay in the 'ON' position. Within 15 seconds.
2. Push the Programming switch 2 times holding in on the 2
starts to flash then release the valet switch. You are now in the Transmitter programming mode.
3. Press the 'Lock' button on the transmitter until a chirp from the horn / a flash from the parking light / the LED turns on
for 2 seconds to confirming the first transmitter is now programmed.
4. Apply the same procedure (step 3) to program 2
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit.
FEATURE PROGRAMM
FEATURE "I" PROGRAMMING:
1. Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.
2. Push the Valet switch 1 times (holding in on the 1
release the valet switch. You are now in the Alarm feature "A" programming mode.
3. Press and release the transmitter button corresponding to the feature you want to program.
Press
One Chirp /
Transmitter
LED one pulse
Button
Factory Default Setting
H3/2 White/Blue = 1 Pulse Remote
1.
Start
H3/8 Pink Wire = Factory Security
2.
Disarm Signal Output
3.
+
H2/4 Brown Wire = Horn Output
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit.
FEATURE "II" PROGRAMMING:
1. Turn the Ignition 'switch 'ON/OFF' 3 TIMES and stay in OFF position.
2. Push the Valet switch 2 times (holding in on the 2
release the valet switch. You are now in the Alarm feature "A" programming mode.
3. Press and release the transmitter button corresponding to the feature you want to program.
Press
One Chirp /
Transmitter
LED one pulse
Button
Factory Default Setting
Button Two Push
1.
Remote
Without ignition
controlled door locks &
2.
unlocks
3.
+
Gasoline Engine
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will confirm exit.
RS-603 REV A.
nd
push, until a long chirp from the horn (optional) and the LED
nd
.
, 3rd and 4th
st
push) until one chirp with one long chirp is heard, then
Two Chirps /
LED two pulse
H3/2 White/Blue = 3 Pulse
Remote Start
H3/8 Pink Wire = Start Status
(Shock Sensor Bypass Control)
Output
H2/4 Brown Wire = Rearm
Signal Output
nd
push ) until two chirps with one long chirp is heard, then
Two Chirps /
LED two pulse
Button One push
Remote Start
Ignition controlled door
locks & unlocks
Diesel Engine and 10
seconds warn-up timer
11
Three Chirps/
LED three pulse
H3/8 Pink Wire = 20
Second Ground out Key
Sensor By-pass
Three Chirps /
Four Chirps /
LED three pulse
LED four pulse
Diesel Engine and
Diesel Engine and 20
15 seconds
seconds warn-up timer
warn-up timer
7/9/2008