- ページ 14

リモートスターター Autopage RS-602のPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Autopage RS-602 16 ページ。 Professional remote car starter
Autopage RS-602 にも：操作マニュアル (8 ページ)

ページを印刷する

Neutral Safety Switch input fail.

No RPM or

Low Voltage.

Over-rev

System timed out

Transmitter

Tach. Signal has not been learned

There are 5 reasons why the remote start

1. The Black/White Neutral Safety wire is not grounded. Must be grounded to start.

2. Hood Pin switch White/Black wire has a ground present. Must not show ground to start.

3. Brake pedal switch White/Violet has 12 volt present. Must not show 12 volt to start.

4. The system is in Valet mode.

5. The remote start feature programming has not been programmed to start the vehicle. The remote start must be

programmed how to start the vehicle.

Caution!! The following procedure must be performed after the installation of the Remote Start Device. It is the

responsibility of the installing technician to complete these tests. Failure to test the unit in the following manner may result in

personal injury, property damage, or both.

1. Test the BRAKE shutdown circuit: With the vehicle in park (P), start the vehicle using the remote transmitter, Once the

engine is running, press the brake pedal. The vehicle should shut down immediately. If the vehicle continues to run, check

the brake circuit WHITE/ VIOLET wire (H3/3) connection.

2. Test the HOOD PIN shutdown circuit: Start the vehicle using the remote transmitter, Once the engine is running, pull the

hood release and raise the hood. The vehicle should shut down immediately. If the vehicle continues to run, check the

hood pin WHITE/ BLACK wire (H3/4) connection.

3. NEUTRAL START SAFETY TEST:

1. Set the vehicle parking brake.

2. Block the drive wheels to prevent vehicle movement.

3. Sitting in the vehicle, turn the ignition switch to "ON" or "RUN" position. But do not start the engine.

4. Step on the brake pedal and shift the gear selector into "DRIVE" (D).

5. Put your foot over the brake pedal but do not press down on it. Be ready to step on the brake to shut down the Remote

Start Device.

6. Start the vehicle using remote transmitter.

a. If the starter does not engage, the test is complete.

b. If the starter engages, immediately step on the brake pedal to shut down the system, recheck your VIOLET wire

(H1/1 starter output wire) connection. The heavy gauge VIOLET wire must be connected to the ignition switch side of

the Neutral Start Switch. If the vehicle you are working on does not have an Electrical Neutral Safety Switch, it will be

necessary to reconfigure the Remote Starts Wiring to accommodate this vehicle. The information concerning the

Mechanical Neutral Safety Switch provided below will help you to determine if the vehicle you are working on has this

type of safety switch and will provide alternate wiring methods to accommodate this situation.

MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERATIONS:

Mechanical neutral safety switch configurations differ slightly in that they do not offer the same level of safety when installing

a remote start device. Often when the ignition switch is turned off while the gear selector is in any position other than park or

neutral, the mechanical function will not allow the key to be turned to the start position or be removed from the ignition

cylinder. This configuration prevents mechanical operation while the vehicle is in gear but offers no consideration for

electrical operation. Because of this potential problem, this installation requires the additional connection of a safety wire

RS-602 REV A.

4. Move the Enable Toggle Switch to "ON"

position. (If installed.)

5. Move the gear selector to "Park"/ "NEUTRAL"

position.

6. Check H3/4 Black/White wire connection.

TACHOMETER CHECKING TYPE:

Check H3/1 White/Red wire connection

VOLTAGE CHECKING TYPE:

Program the "CHECK LEVEL" from

"Hi Check Level" to "Low Check Level"

Re-learning the RPM (Feature

TROUBLE SHOOTING

button will not respond from the transmitter.

TESTING YOUR INSTALLATION:

6/18/2007

III – 2

)