リモートスターター Autopage XT-12のPDF クイック・スタート・インストール・マニュアルをオンラインで閲覧またはダウンロードできます。Autopage XT-12 2 ページ。 Remote car starter
Autopage XT-12 にも： クイック・スタート・インストール・マニュアル (2 ページ)
ページを印刷するQUICK START INSTALLATION GUIDE
Help Auto Page protect our environment !
If you are not proficient in the installation of this product or would
like a full version of the installation manual, Please visit our web
site @
www.autopageusa.com
FOR PROFESSIONAL INSTALLATION ONLY!
RX-300A
FUSE
Valet
Switch
FUSE
H5
H4
H7
H1 6 Pin Wht.
ANT.
Valet
LED
C3-RS-601
H6 DL
H3 10 Pin White
H8
H2 5 Pin
Green : (-) Lock
(+) Unlock
Door Locks
Blue : (-) Unlock
(+) Lock
White/Red : Tachometer Signal Input
White/Blue : Instant Start (-) Input
White/Black : Safety, Hood Pin Input (-)
Black/White : Neutral Safety Switch (-) Input
White : Ground When Running By-pass Control Output
White/Violet : Safety Shutdown Brake Input (+)
H1 6 PIN HEAVY GAUGE WIRE HARNESS
20A
Red: Remote Start Power 1
20A
Red: Remote Start Power 2
Violet: Starter (+) Output
Pink: Ignition 2 (+) Output
Yellow: Ignition 1 (+) Output
Brown: Acc/Heater (+) Output
H5 5 PIN WIRE HARNESS
Red/White: Parking Light Relay Power Input
Violet : Starter Output
White: Parking Light Relay Output
Red : 12 Volt Input
Black: System Main Ground (-)
Red : 12 Volt Input
Yellow. Ignition 1 Output
Brown: Siren (+) Output
Pink : Ignition 2 Output
Red: 12v + Battery Power
Brown ACC Output
PROGRAMMING TRANSMITTER
LED Indicator
Note: This model will only retain the last 4 remote transmitters programmed. If the
transmitter memory is exceeded, the security system will start deleting transmitters from
memory in chronological order.
1. Turn the Ignition 'switch „OFF/ON‟ 3 TIMES and stay in ON position.
"Within 15 seconds".
2. Push the Valet switch 2 times and hold it on the 2
then release the valet switch. You are now in the Transmitter programming mode.
3. Press and hold any button of the transmitter until the siren responds with a confirming
chirp, indicating the signal has been stored into memory.
4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3
for remaining transmitters.
FEATURE PROGRAMM
FEATURE "I" PROGRAMMING:
1. Turn the Ignition 'switch „ON/OFF‟ 3 TIMES and stay in OFF position.
2. Push the Valet switch 1 times (holding in on the 1
long chirp is heard, then release the valet switch. You are now in the Alarm feature
"A" programming mode.
3. Press and release the transmitter button corresponding to the feature you want to
program.
One Chirp /
Press
LED one pulse
Red/White : Parking light Input
Transmitter
Factory Default
Button
White : Parking light Output
Setting
Black : System Ground
H3/2 White/Blue
Brown : Programmable Output (-)
= 1 Pulse
1.
Horn (-) or Factory Rearm (-)
Remote Start
FUSE
Red : System Power + 12 Volt
H3/8 Pink Wire =
Yellow : Ignition 3 Output ( 200 mA - )
Factory Security
Disarm Signal
Blue/Black : ACC 2 ( 200 mA - )
2.
Output
Pink : 200mA Programmable Output (-)
H2/4 Brown Wire
+
= Horn Output
3.
Gray : CH 3 Trunk Release (-)
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking
light flashes will confirm exit.
FEATURE "II" PROGRAMMING:
1. Turn the Ignition 'switch „ON/OFF‟ 3 TIMES and stay in OFF position.
2. Push the Valet switch 2 times (holding in on the 2
long chirp is heard, then release the valet switch. You are now in the Alarm feature
"A" programming mode.
3. Press and release the transmitter button corresponding to the feature you want to
program.
One Chirp /
Press
LED one pulse
Transmitter
Factory Default
Button
Setting
Button Two
1.
Push Remote
Without ignition
controlled door
2.
locks & unlocks
Gasoline Engine
+
3.
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking
light flashes will confirm exit.
FEATURE "III" PROGRAMMING:
1. Turn the Ignition 'switch „ON/OFF‟ 3 TIMES and stay in OFF position.
2. Push the Valet switch 3 times (holding in on the 3
chirp is heard, then release the valet switch. You are now in the Alarm feature "A"
programming mode.
3. Press and release the transmitter button corresponding to the feature you want to
program.
Press
Transmitter
Button
1.
2.
nd
push until a long chirp is heard
+
3.
Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 long chirps & 3 parking
light flashes will confirm exit.
FEATURE "IV" PROGRAMMING:
st
push) until one chirp with one
1. Turn the Ignition 'switch „ON/OFF‟ 3 TIMES and stay in OFF position.
2. Push the Valet switch 4 times (holding in on the 4
chirp is heard, then release the valet switch. You are now in the Alarm feature "A"
programming mode.
3. Press and release the transmitter button corresponding to the feature you want to
program.
Two Chirps /
Three Chirps/
LED two pulse
LED three pulse
Press
Transmitter
Button
H3/2 White/Blue = 3
Pulse Remote Start
1.
H3/8 Pink Wire =
H3/8 Pink Wire = 20
Start Status (Shock
Second Ground out
Sensor Bypass
Key Sensor By-pass
Control) Output
2.
H2/4 Brown Wire =
Rearm Signal Output
+
3.
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will
confirm exit.
FEATURE "V" PROGRAMMING:
1. Turn the Ignition 'switch „ON/OFF‟ 3 TIMES and stay in OFF position.
2. Push the Valet switch 5 times (holding in on the 5
nd
push) until one chirp with one
chirp is heard, then release the valet switch. You are now in the Alarm feature "A"
programming mode.
3. Press and release the transmitter button corresponding to the feature you want to
program.
Press
Two Chirps /
Three Chirps /
Four Chirps /
Transmitter
LED two pulse
LED three pulse
LED four pulse
Button
Button
1.
One push
Remote Start
Ignition
2.
controlled
door locks &
unlocks
+
3.
Diesel Engine
Diesel Engine
Diesel Engine
Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will
and 20
and 10 seconds
and 15 seconds
confirm exit.
seconds warn-
warn-up timer
warn-up timer
up timer
C3-RS-601
rd
push) until one chirp with one long
One Chirp /
LED one
Two Chirps /
Three Chirps /
Four Chirps /
pulse
LED two pulse
LED three pulse
LED four pulse
Factory
Default
Setting
20 minutes
10 minutes run
30 minutes run
5 minutes run
run time
time
time
time
0.8-second
3.5-second
0.8 second
0.8 second dbl
Door lock &
Door
lock, 0.35
lock,0.8 second
Unlock.
Lock & Unlock.
second unlock
dbl unlock
Five chirps= 0.8 second lock, dbl 0.8 second unlock
Six chirps= dbl 0.8 second lock, 0.8 second unlock
Door Lock
before & after
This Remote Starter with Alarm and Keyless Entry System
start * This is the
Door Lock
Door Lock after
preferred setting
Without this
has been designed to be installed on fuel-injected vehicles
before start
start
when using the
feature
with an automatic transmission ONLY.
optional XT-11
single button
remote
transmission vehicle.
safety switch so it will not start in any forward or reverse
gear.
vehicles with a purple starter wire have a mechanical-type
th
push) until one chirp with one long
park safety switch instead of electrical safety switch. The
mechanical type does not interrupt the starter circuit when
the transmission is in any gear and does not offer the 100%
level of safety required for remote starting purposes.
Therefore, our system should never be installed on any
One Chirp /
vehicle that uses a mechanical type park safety switch.
LED one
Two Chirps /
Four Chirps
pulse
Three Chirps /
LED two pulse
/ LED four
Factory
LED three pulse
pulse
vehicle will not start in any forward or reverse gear,
Default
Setting
regardless of the type of vehicle.
DBI TACH
Tachometer
Voltage checking
Timer checking
**
checking type.
type
type
DATA
or steering linkage.
ONLY !!
RPM learning
immobilizer system that can severely complicate the
0.8-second (2 chirps), 1.0-second (3 chirps), 1.2-second (4
Start Timer:
chirps), 1.4-second (5 chirps), 1.6-second (6 chirps), 1.8-
installation. There is a possibility that this system cannot be
0.6-second
second (7 chirps), 2.0-second (8 chirps), 3.0-second (9
installed on some immobilizer-equipped vehicles.
chirps), 4.0-second (10 chirps),
Low ceck
Hi check level
extreme care and do not probe any wires of the SRS
level
system.
vehicle.
that no wiring harness or other components are located
behind the panels that would otherwise be damaged.
th
push) until one chirp with one long
Poor wiring, i.e. taped joints will possibly introduce
unreliability into the alarm system and may result in false
alarms or incorrect operation. We suggest soldering all
One Chirp /
Four
connection points.
Two Chirps /
LED one pulse
Three Chirps /
Chirps /
LED two pulse
Factory
LED three pulse
LED four
prevent possible damage to wires.
Default Setting
pulse
Second
Second Start
Accessory
H3/9 Blue/Black
H3/9 Blue/Black
+ 50 RPM
No RPM learning
DBI ONLY
- 50 RPM
No RPM Learning or < 50RPM
DBI ONLY
FEATURE "V" MUST BE PROGRAMMED FOR THE
UNIT TO RESPOND TO REMOTE START!
If you are not sure or do not understand any part of
the quick start guide, please download the complete
installation
manual
available
at
www.autopageusa.com
.
This quick start guide is a
brief outline for professional installers that are
familiar with the installation and operation of this
remote start system.
Please test all of your
installation to insure proper operation of the vehicle
before returning it to the customer.
For authorized dealer technical support, please call
800-945-2527
and
wait
for
the
first
available
technician.
Technical support hours are Monday
through Saturday from 8:00 to 5:00 Pacific standard
time.
Never
install this
remote starter
on
a manual
This system must be installed and wired through a
Some automatic transmission vehicles mainly older GM
Once you install this system, you must verify that the
Read the operation manual for operating.
Do not install any component near the brake, gas pedal
Some vehicles have a factory installed transponder
Most vehicles have an SRS air bag system. Use
Disconnect the car battery before beginning work on the
Check behind panels before drilling any holes. Ensure
Do not use conventional crimp lock, bullet on any wiring.
Install the wiring neatly under carpets or behind trim to
960 Knox Street Unit B
Torrance, California 90502
Main Office: 310-323-1800
Technical Support: 800-945-2527
(For Authorized Dealers Only)
www.autopageusa.com