- ページ 2
芝生とガーデン用品 Autopot AUTO83.9GALのPDF セットアップマニュアルをオンラインで閲覧またはダウンロードできます。Autopot AUTO83.9GAL 2 ページ。 Aquavalve
ページを印刷する
Auto8 contents
• 1x Auto8 tray
• 3.3ft of piping ¼" pipe
• 1x Auto8 lid
• 8x Root Control PotSock (square)
• 1x Round blue access cover
• 8x Root Control Sheet (square)
• 1x AQUAvalve
• 8x 2.2 gal pot if (AUTO82.2GAL)
• 1x AQUAvalve cover
• 8x 3.9 gal pot if (AUTO83.9GAL)
• 1x ¼" top hat grommet
Pot and Tray Dimensions
22.6"
47"
Required Reservoir Capacity
Auto8
1x Auto8
2x Auto8
System Size
FlexiTank or
FlexiTank
FlexiTank
FlexiTank Pro
/ Pro 25 gal
/ Pro 60 gal
Capacity
•
Pot up your plants, water through, then allow your plants to establish in the pots for a period of 7 to 10 days before
turning your system on. This will encourage a stronger and healthier root system.
•
Always raise your reservoir to a minimum of 6" above the highest AQUAvalve and re-fill the reservoir when there is
approximately a 1/3 of the solution left - NEVER ALLOW THE RESERVOIR TO RUN EMPTY.
•
For best results, we recommend mineral fertilisers. Do not use liquid organic fertilisers, as they have a tendency to
block small pipe work.
•
Clean all substrate from the bottom and sides of the pots before placing in each tray. This will ensure your system
is clean from the start.
•
Always use free draining substrates, for example: soil/perlite, coco/perlite, soil/clay pebbles, coco/clay pebbles,
rockwool/clay pebbles.
[email protected] I www.autopot-usa.com I +(1) 702 338 0373
10.2"
260mm
13.8"
9.6"
3.9 gal
2.2 gal
pot
pot
7.6"
195mm
7.6"
Included with
Included with
4.5"
(AUTO82.2GAL)
(AUTO83.9GAL)
FlexiTank and FlexiTank Pro are the only collapsible reservoirs
that AutoPot recommend for use with Auto8 Tray Systems.
A minimum 25gal reservoir is required per unit.
4x Auto8
8x Auto8
10x Auto8
FlexiTank
FlexiTank
FlexiTank
/ Pro 105 gal
200 gal
265 gal
Advice
Auto8 Setup
1
Put one square root control
sheet into each of the pots.
Sheets should be put
in gold face down.
3
Once pots have drained
fit a PotSock Square over
the base of each pot.
5
Push ¼" top hat
grommet into the hole
in the Auto8 tray wall.
Thread ¼" pipe into the
tray through the grommet.
7
Cut ¼" pipe to
appropriate length.
Connect via ¼" /
½" fittings to a filter
(not included).
Connect filter to
reservoir. Leave tap off.
9
Remove any slack
from ¼" pipe by
drawing excess pipe
out of the tray.
Ensure that the circular
spirit level indicates
the tray is level,
adjust if required.
Allow your plants to establish for 7-10 days before turning system on
Advice
If you require any guidance email - [email protected]
2
Fill pots with medium
and pot up plants.
Water through pots
and allow to drain
outside the tray.
4
Make sure the pots are
clean and free of debris.
6
Remove AQUAvalve
collar.
Push ¼" pipe through
collar and attach to
AQUAvalve nozzle.
Rescrew collar - DON'T
overturn... when you
feel it grip STOP.
8
Place AQUAvalve cover
over the AQUAvalve.
The AQUAvalve and
cover should be placed
directly onto the tray.
10
Make sure the
system is clean and
free of debris.
Place the lid on top
of the tray. Insert the
pots. Place the round
blue access cover
over the valve.