- ページ 5
楽器アンプ Gallien-Krueger Backline 100のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Gallien-Krueger Backline 100 6 ページ。
ページを印刷する
Suggested
G-K Systems
Putting together the right system is as important
to your final sound as choosing the right amplifier
or the right guitar. Here are our favorite systems,
each designed to optimize the power and
versatility of the BackLine 100 Combo and
Head. For the ultimate system, use GK cabinets,
the only cabs specifically designed for GK
electronics.
Backline 100
Block Diagram
Specifications
Max input :
1.4Vrms
Output :
70W into 8
100W into 4 (@ less than 5% THD)
Signal - to - Noise Ratio : (Clean Channel) 35mVrms @ 1KHz
(Lead Channel) .4mVrms @ 1Khz
Return Sensitivity :
.58Vrms @ 1KHz
Clean Equalization :
Mid : +4, -5dB @ 400Hz
w/Shift : +3, -6dB @ 700Hz
Treble : +6, -12dB @ 2KHz
Bass : +4, -10dB @ 80Hz
Troubleshooting
Your new amp, if handled with care, should give you
trouble-free performance. If operated according to
instructions in this manual, your only maintenance
should be occasional external cleaning.
Often when an electrical component provides
poor, erratic, or no performance, it is due to minor
problems or irregularities which may be corrected
easily by someone knowing very little about elec-
tronics.
We have provided the accompanying chart for
your reference. If you have any problems at all,
please check this list first. If your problem is major
and there is definitely something wrong with the
unit, please refer to the list of GK Authorized
Service Centers included with the paperwork in the
packing box. If necessary, call your local GK Dealer
to locate you nearest GK Authorized Service Center.
You may also call our Service Department at (408)
441-7970, ext.38 for reference to your nearest GK
Authorized Service Center.
Lead Equalization :
Presence :
Input Impedance :
Output Impedance :
Reverb :
Dimensions :
Footswitch :
PROBLEMS:
LEDs light but no signal from Speaker Outputs,
Headphones, or Line Outputs:
LEDs light, tone and volumes turned up but no sound.
LEDs light, tone and volumes up, speakers and
connections OK, but no signal from output.
Channel Switching or Lead Mode Select not
functioning with footswitch plugged in and
appropriate LED indicators "on".
Loud hum.
Excessive noise.
After playing for some time, the unit becomes
hot to touch and shuts off 0 no LEDs lit or
signal coming out.
Amp is not hot to touch and still no power
no LEDs lit or signal coming out.
Mid : +4, -8dB @ 800Hz
w/Shift : +3, -5dB @ 500Hz
Treble : +5, -6dB @ 4KHz
Bass : +2, -3dB @ 80Hz
+2, -3dB @ 4KHz
Input ...........................1 M
Return ........................100K
Send ...........................3 K
Line Out (Recording Compensated ) ...........1KW
3 - Spring Accutronics
112 Combo : 19'' W x 17''H x 12''D (42lbs.)
Head : 21''W x 9''H x 9.7''D
GK RF2 and standard 3-connector stereo cord (1/4''
plugs)
PROBABLE CAUSES/SOLUTIONS:
Be sure all tone controls and volumes are turned up at
least part way.
Check Interconnections with speakers.
Check guitar volume, pick-ups, cord, and repair or
replace if necessary.
Be sure front panel On/Off buttons are "in", Check
footswitch cable.
Check grounding of the unit and any effects going
through the effects loop. Proper grounding is mandatory.
Repair or replace guitar cord. Make sure external effects
are patched into the Send and Return and not before the
Input. Test guitar pick-ups.
Turn off power switch and allow unit to cool off. Turn on
power again. If is comes on, make sure speaker load is
no less than 4 ohms or that unit is not affected by another
heat source (stage lighting, direct sunlight, etc.)
Check power cord, AC outlet and fuse. If all are OK or
fuse is blown, call your local GK Authorized Service
Center. Note : Be sure the correct fuse is being used.