- ページ 4
カッター maimin SABRE 3000のPDF 取扱説明書＆パーツマニュアルをオンラインで閲覧またはダウンロードできます。maimin SABRE 3000 20 ページ。 Straight knife cutting machine with flexi-band sharpener
maimin SABRE 3000 にも： 取扱説明書とパーツリスト (12 ページ)
ページを印刷する2.9
TO REMOVE SHARPENER FROM MACHINE
(Figure
6)
a)
Run
sharpener
to
lowest
position,
turn off motor
and
disconnect
power.
b)
Figure
6:
Disengage
Tripper Handle
"A"
by
inserting
handle
of
Knife
Key
"B"
through hole in lower
cover and pressing
upwards
until Tripper
Handle
snaps
back to its
"off
'
position.
c)
RemoveScrew.4'390holdingClampPlate,4'394
against
Band
Plate
Guide ,4393
and
remove Guide
and Plate.
d)
With
3/8" wrench remove
2
Nuts
,4.344
and
2
Washers
,4'343
holding
Brake
4342, andremove Brake.
e)
RemoveScrew ,{316 holding
Shafts
Cover
4315,
and
lift
offCover.
f)
Remove
3
Nuts
4'328
and
1
Nut
5
10B (at
lower left
rear
corner
of
sharpener)
which hold
Drive
Housing
4327.
g)
Pull
sharpener
forward gently to
remove.
2.10 TO ATTACH SHARPENER TO MACHINE
a)
Disconnect
power.
b)
Wipe oil from outer diameter
of
CrankA5O5
andPulleyA303.
c)
Place sharpener
onto
3
mounting
Screws ,4'521
on,Front
Housing.
I
d)
Add
and
tighten
3
Nuts ,{328
and
Nut
5108
on
back
of
Sarpener.
III. TROUBLE SHOOTING GUIDE
3.1 MACHINE TROUBLE SHOOTING
Symptom
Possible Cause
e)
Add
Band
Plate
Guide A393
and
Clamp
Plate 4'394.
f)
Hold
Guide
against Standard
,4.564
and
tighten
Screw
4390.
g)
Lower
Presserfoot Leg
to
Baseplate, connect power,
and
run
sharpener
to
its
top position. Disconnect power.
h)
Add
Shafts Cover
4315.
i)
Add
Brake A342.
2.11 TO SET POSITION OF BAND PLATE
CARRIER 4374 (Figure
7)
a)
Run sharpener to highest
position, turn off motor,
and
disconnect
power.
b)
Figure7: Measure distance between
Cover
"A"
(A361)
and
top of
Gear
Case
"B"
(4367).
Maximum
distance
is25132"
(2
cm)
when
Screw 4'363
is
adjusted
properly.
c)
If
distance
is
greater, loosen
Nut
.4'366
and
lower
Screw
A363
a
few turns.
Tighten Nut,
run sharpener, and measure again.
d)
FlexiBands
,4'386
must
not touch blade
,4'574
when sharpener
is
at
top position.
2.12TO REMOVE
MOTOR COVER A579
(Figure
8)
Disconnect
Power. Loosen the
3
Screws A,580,
and slide
Motor
Cover off.
v
v
1.
Bottom
comer of
blade breaks.
2.
Motor
slow
in
reaching
ftrll
speed.
3.
Motor
binds at one spot.
4.
Motor
becomes
hot.
5.
Motor
rotates
wrong
way.
6.
Motor
does
not
start.
7.
Terminal
Block and/or Connector
becomes
very hot.
8.
Machine
does
not
roll
freely
on
table.
a) Inserts
(,4'558)
badly worn.
b)
Ifuife
strikes
throat plate.
If
cutting hard
materials,
use
wide
slot
throat plate.
a)
Low voltage
or
wrong
voltage.
b) Three
phase:
(1) Fuse
out
on one
phase.
(2) Ground wire incorrectly
connected
to
machine.
a) Crosshead
(4'510)
and
Gibbs (A513) tight.
b)
Standard
(4'564) not in alignment
with
Crosshead
(,{510).
c) Standard
(,4'564)
bent.
a)
Lint
and dust inside
Motor
Cover (A579).
b) Three
phase:
one
phase
not working.
a)
Three
phase:
Wiring
incorrect.
Change any
two
wires
in
Terminal
Block
(A522) or Connector (A525).
a)
Connector
(4.525)
not
firmly
attached
to Terminal
Pins
(4523\.
b)
Switch
(,4,550)
defective.
c)
Starting
Switch
or Relay (4'540) and/or Capacitor (4'543)
defective.
d) Broken Jumper Wire. (Capacitor to Starting
Switch
or Relay)
a) Inserts
in Connector (A525) worn.
Change
Connector.
b) Terminal
Pins
(4523) wom.
a) Surface
of cutting table not
smooth.
b)
Cushions
(4'561) in
Roller
Carriers
compressed causing
Baseplate
(4'560) to
drag on table.
4
I