- ページ 5

ゲートオープナー Dea ghost 200LのPDF 取扱説明書および警告をオンラインで閲覧またはダウンロードできます。Dea ghost 200L 17 ページ。 Underground electro-mechanical operator for swing gates
Dea ghost 200L にも：取扱説明書 (16 ページ)

ページを印刷する

Operating instructions and warnings

4.5.5 Adjustment

In order to install standard products no adjustment is requi-

red; while to install GHOST 200 with the accessory "mechanical

stop art. 218" you will only have to position the stop blocks by

unscrewing their fixing screws; then position them correctly, have

them run along the apposite slots and tighten up the two screws

again (see F6 page 32)

WARNING All the other adjustment/setting operations beyond

the adjustment of the oil flow are made by the manufacturer.

Tampering with these settings may cause malfunction and/or

situations of risk to people, animals and property. Refrain from

performing any operations not authorised by DEA System.

4.5.6 Maintenance and repair

Good preventive maintenance and regular inspection ensure

long working life (see also "Warranty"). Consult the "TROUBLE-

SHOOTING" table (see page 9) whenever anomalies are obser-

ved in order to find the solution to the problem and contact DEA

System directly whenever the solution required is not provided.

The inspection/maintenance operations to be routinely sche-

duled in the "complete automation maintenance handbook" are:

INTERVENTION TYPE

cleaning of external

checking of screw tightening

checking of release

mechanism operation

check that water flows out properly

from the foundation box

greasing of articulated joint

WARNING Before doing any maintenance operation take off

the foundation box lid (by unscrewing the two fixing screws;

see F5 page 30); this lid offers protection against the risk of

scissor movement due to the presence of moving levers. Once

the maintenance operation is completed place back immedia-

tely this protection.

WARNING All installation, maintenance, cleaning or repair

operations on any part of the system must be performed

exclusively by qualified personnel with the power supply

disconnected working in strict compliance with the electrical

standards and regulations in force in the nation of installa-

tion.

WARNING The use of spare parts not indicated by DEA Sy-

stem and/or incorrect re-assembly can create risk to people,

animals and property and also damage the product. For this

reason, always use only the parts indicated by DEA System

and scrupulously follow all assembly instructions.

4.6

Training

After installation and setting, the correct operation of the com-

plete automatism must be carefully illustrated to the final user.

GHOST 200 gate operator requires careful instruction on

the release mechanism (see "Enclosures") and on the specific

maintenance schedule (see Point 4.5.6.).

WARNING Awareness of the operation of GHOST 200 key-

release mechanism (see F8 Page 32) is essential for all users

of the automatism because failure to use the device quickly

during emergencies can jeopardise people, animals and pro-

perty. Enclosure I to these instructions, which the installer is

required to deliver to the final user, illustrates operation and

can be detached.

4.7

Inappropriate use

Chapter "4.4 Appropriate conditions of use" describes the

conditions for which the product has been designed and tested.

The product must never be used for other purposes.

GH O ST 2 0 0

PERIODICITY

6 months

1 year

WARNING The use of the product under unusual conditions

not foreseen by the manufacturer can create situations of dan-

ger, and for this reason all the conditions prescribed in these

instructions must be respected.

WARNING Under no circumstances must the product be

used in explosive atmospheres or surroundings that may prove

corrosive and damage parts of the product.

5 SPARE PARTS LIST

The list of spare parts that can be ordered (Pages 28 and

29) is a detailed list that accompanies the exploded view of the

product and must be used to order spare parts.

The following data must always be provided when ordering

spare parts:

• the code of the product (seen on the product label; see F7,

Page 32),

• the part's position number in the exploded view,

• if available, the product's purchase date may be useful in

some cases.

6 COMPLETE CLOSING ASSEMBLY

This chapter illustrates the typical installation of a complete

automation for the purpose of informing and assisting the instal-

ler in the selection of the various parts to be used in compliance

with Machinery Directive (2006/42/CE) and European Safety

Standards (EN 12453 - EN 12445) for gate installation.

The data provided in this chapter are neither complete nor

exhaustive, and DEA System declines all liability for any errors,

omissions or inaccuracies that may occur.

6.1

Minimum level of protection provided by the sa-

fety edge

Among the most serious risks to be considered when auto-

mating of a swing gate is the risk of crushing between two wings

or between one wing and its stop during closing. Regulations

prescribe the adoption of one of the following types of controls

against such risks depending on the use foreseen for the gate.

An appropriate type of operating control board must be used

according to the gate type and according to its usage, as provided

for by the quoted regulations (see "OPERATING CONTROL" table).

6.2

Risk of crushing in the opening area

The risk of being crushed can also arise in the area between

the gate opening and the wall or fence behind it. F9 on Page

32 provides the measurements that must be observed whenever

measures are not taken to limit the impact force or whenever

presence detection systems are not used.

6.3

Impact in the opening/closing area

In order to avoid being crushed by the gate wing in the clo-

sing area, install a pair of photocells (A) (recommended height:

500 mm) in order to detect the presence of the test parallelepiped

(B) (height: 700 mm) positioned as shown in F10 on Page 32.

Note. The presence detection test sample is a parallelepiped

with 3 sides with light-coloured reflecting surfaces and 3 sides

with dark-coloured, opaque surfaces.

In order to further reduce the risk of impact with the gate

wing in the opening area, an extra pair of photocells (C) (re-

commended height: 500 mm) can be installed for the detection

of the presence of the test parallelepiped (D) (height: 700 mm)

positioned as shown in F10 on Page 32.