- ページ 11

エアコン Green DS540059のPDF ユーザーマニュアルとインストールハンドブックをオンラインで閲覧またはダウンロードできます。Green DS540059 19 ページ。 Electric air-conditioning unit green gt790 12.000btu 12v

ページを印刷する

INSTALLATION

INSTRUCTIONS

Before the air-conditioner is installed at the first

time, check if you have received all necessary

components and accessories

•

Outside (Condenser Unit): Choose

the position and place for the

installation and make 6 holes at the

driving cabin. Fixation screws shall

be of type MB Grau 12.9. A padded

damping must be placed between

the external unit and the driving

cabin.

•

Inside

(Evaporator

Unit):

recommended the internal unit to

be installed at the right side of the

passenger's seat. First, assemble a

wooden board at the driving cabin

with self-tapping screws. Screws

might also be used to break the board

and fix it on the cabin bar. 4 screws

should be used, at least). After the

wooden board is fixed, use self-tap-

ping screws to fix the Evaporator

Unit along with the wooden board.

On each side of the Evaporator Unit

there are 3 screw-holes, if necessary,

screws must only be inserted.

Electric Air-Conditioning Unit Green GT790 12.000BTU 24V - DS540059

Electric Air-Conditioning Unit Green GT790 12.000BTU 12V - DS630051

•

After the Condenser Unit and the Evapora-

tor Unit are fixed, connect the pipes and

install the Expansion Valve. During installa-

tion, observe if part of the valve junction

and the connection pipe are clean. Check if

the sealing ring is NOT damaged and pour

in the appropriate quantity of refrigerant

before installation is made.

•

Connection of power cables:

- All electric cables of the Evaporator Unit

and Condenser Unit come with the spe-

cific connectors;

- Organize the wires to avoid any wrong ca-

ble crossing;

- During the installation of battery cables,

it is extremely important to check if the

positive (red) and negative (black) poles

are not inverted;

- If the power cable length is too short, you

might extend it for a maximum of 1,5m

and, the connector must be protected

(waterproofed).

IMPORTANT:

The air-conditioning

power cable shall be connected to

the battery´s positive and negative

terminal connectors, only, after the

Evaporator Unit and the Condens-

er Unit are installed. And, the total

length of the power cable shall NOT

be longer than 5 meters.

•

For the system´s vacuuming process

it is essential to use a specialized

vacuuming pump:

- Connect the (high/low pressure)

hoses along with the vacuuming

pump to the Condenser Unit;

- Open Manometer (high/low pres-

sure) valves, completely;

- Start the vacuuming process for,

approximately 20 minutes, check

if all pressurized air has been emp-

tied from the system. After doing

ATTENTION: The system is filled in with oil before its delivery.

After first installation, do not complete with more oil. In case of

any refrigerant leakage while the air-conditioner is being used,

add 80mL of oil. But you should use high-quality oil (ISO VG68).

Electric Air-Conditioning Unit Green GT790 12.000BTU 24V - DS540059

Electric Air-Conditioning Unit Green GT790 12.000BTU 12V - DS630051

so, close (high/low) pressure valves

and wait for 10 minutes. Check if

the manometer´s pressures re-

main unchanged, and only, then,

it is possible to fill in with Refriger-

ant R134a without contrast;

- After the refrigerant has been

filled into the system, turn on the

air-conditioner and check if high/

low pressure figures are according

to the normal parameters (high

pressure:

1.2-1.4,

low

pressure:

0.2-0.25);

- With the air-conditioning system

on, test all the air-conditioner´s

operational modes, checking if all

functions are on normal opera-

tion. After the device turns back to

its normal function, turn it off and

wrap in the connection pipes with

binders. Then, apply sealant and,

finally, install the boards to close

the holes.