- ページ 3

クックトップ KitchenAid KECC051HWH1のPDF 取付説明書をオンラインで閲覧またはダウンロードできます。KitchenAid KECC051HWH1 8 ページ。 15", 30" and 36" electric built-in ceramic cooktops
KitchenAid KECC051HWH1 にも：パーツリスト (3 ページ), 取付説明書 (7 ページ)

ページを印刷する

Electrical requirements

If codes permit and a separate ground wire is

used, it is recommended that a qualified

electrician determine that the ground path is

adequate.

Do Not ground to a gas pipe.

Check with a qualified electrician if you are

not sure the cooktop is properly grounded.

Do Not have a fuse in the neutral or ground

circuit.

IMPORTANT:

Save Installation Instructions for electrical

inspector's use.

A three-wire or four-wire, single phase,

240-volt, 60-Hz, AC-only electrical supply is

required on a separate, 40-ampere circuit, (Note:

The KECC051 series requires a 20-ampere

circuit), fused on both sides of the line. A time-

delay fuse or circuit breaker is recommended.

The fuse size must not exceed the circuit rating

of the appliance specified on the model/serial

rating plate located on the bottom of the cooktop.

THE COOKTOP MUST BE

CONNECTED WITH COPPER WIRE ONLY.

Wire sizes and connections must conform

to the requirements of the National Electrical

Code ANSI/NFPA 70 – latest edition **, or CSA

Standards C22.1-94, Canadian Electrical Code,

Part 1 and C22.2 No. 0-M91 - latest edition ***

and all local codes and ordinances.

The cooktop should be connected directly

to the fused disconnect or circuit breaker box

through flexible, armored or non-metallic

sheathed, copper cable. The flexible, armored

cable extending from the fuse box or circuit

breaker box should be connected directly to the

junction box.

Locate the junction box to allow as much

slack as possible between the junction box and

the cooktop so that the cooktop can be moved if

servicing is ever necessary. Do Not cut the

conduit.

A U.L.- or C.S.A.-listed conduit connector

must be provided at each end of the power

supply cable (at the cooktop and at the junction

box).

Copies of the standards listed may be obtained from:

** National Fire Protection Association

Batterymarch Park

Quincy, Massachusetts 02269

*** Canadian Standard Association

178 Rexdale Boulevard

Etobicoke (Toronto), Ontario M9W 1R3

Electrical connection

For model KECC051 series only:

WARNING

Electrical Shock Hazard

Turn power supply off before connecting

wires.

Use 12-gauge solid copper wire.

Electrically ground cooktop.

Failure to follow these instructions can

result in death, fire, or electrical shock.

This cooktop must be connected to a

grounded, metallic permanent wiring system or

a ground connector should be connected to the

ground terminal or wire lead on the cooktop.

This cooktop is manufactured with a frame

connected, green or bare ground wire. Connect

the cooktop cable to the junction box through the

U.L.- or C.S.A.-listed conduit connector.

Complete electrical connection according to local

codes and ordinances.

Panel B

For all models except KECC051 series:

WARNING

Electrical Shock Hazard

Turn power supply off before connecting

wires.

Use 8-gauge solid copper wire.

Electrically ground cooktop.

Failure to follow these instructions can

result in death, fire, or electrical shock.

This cooktop must be connected to a

grounded, metallic permanent wiring system

or a ground connector should be connected

to the ground terminal or wire lead on the

cooktop.

This cooktop is manufactured with a frame

connected, green or bare ground wire. Connect

the cooktop cable to the junction box through the

U.L.- or C.S.A.-listed conduit connector.

Complete electrical connection according to local

codes and ordinances.

For all cooktop models with three-

wire cable from the cooktop:

Where local codes Do Not permit

connecting the frame-ground conductor to

the neutral (white) junction box wire. (Used

for Canadian installations):

4-wire cable from power supply

red wires

bare or green

ground wires

U.L.- or C.S.A.- listed

conduit connector

3-wire cable from cooktop

Ungrounded neutral

Figure 1

1. Disconnect power supply.

2. Connect the flexible, armored cable from the

cooktop to the junction box using a U.L.- or

C.S.A.-listed conduit connector. Tighten screws

on conduit connector.

3. Connect the two black wires together; then

connect the two red wires together using twist-

on connector. (See Figure 1.)

4. Connect the green or bare ground wire from

the cooktop cable to the grounded wire in the

junction box or other grounded connector

using twist-on connector.

5. Put a twist-on connector on end of white wire.

Do Not connect bare ground wire to neutral

(white) wire in junction box.

Where local codes permit connecting

the frame-ground conductor to the neutral

(white) junction box wire. (Not used for

Canadian installations):

3-wire cable from power supply

red wires

white wire

bare ground wire

U.L.- or C.S.A.- listed

3-wire cable from cooktop

conduit connector

Grounded neutral

Figure 2

1. Follow steps 1 and 2 from "A" above.

2. Connect the bare cooktop wire with the white

wire; the two red wires together; and the two

black wires together using twist-on connectors.

(See Figure 2.)

For all cooktop models with four-wire

cable from the cooktop. (These

cooktops are manufactured with white

(neutral) power supply wire and a

cabinet-connected bare ground wire

factory-crimped together.):

Where local codes Do Not permit

connecting the frame-ground conductor to

the neutral (white) junction box wire: (Used

for Canadian installations):

4-wire cable from power supply

red wires

bare or green

wires

4-wire cable from cooktop

1. Disconnect power supply.

2. Connect the flexible, armored cable from the

cooktop to the junction box using a U.L.- or

C.S.A.-listed conduit connector. Tighten screws

on conduit connector.

3. Connect the two black wires together; then

connect the two red wires together using twist-

on connectors. (See Figure 3.)

4. Separate the factory-crimped bare and white

cooktop cable wires.

5. Connect the two white wires together using

junction box

twist-on connectors.

6. Connect the bare ground wire from the

cooktop cable to the grounded wire in the

white wire

junction box or other grounded connector

using twist-on connector. (See Figure 3.)

Do Not connect bare ground wire to neutral

twist-on

connector

(white) wire in junction box.

black wires

Where local codes permit connecting

the frame-ground conductor to the neutral

(white) junction box wire. (Not used for

Canadian installations):

junction

box

red

wires

white

wire

white and bare

grounding oven cable

wires — factory crimped

4-wire cable from cooktop

1. Follow steps 1 and 2 from "A" above.

2. Connect the two black wires together; the two

red wires together; and the factory-crimped

bare and white cooktop cable wires to the

white (neutral) wire in the junction box using

twist-on connectors. (See Figure 4.)

junction box

Where local codes Do Not permit

twist-on

connectors

connecting the frame-ground conductor to

the neutral (white) junction box wire:

1. Follow steps 1 and 2 from "A" above.

2. Connect the two black wires together and the

black wires

two red wires together.

3. Separate the factory-crimped bare and white

cooktop cable wires.

4. Connect the two white wires together using

twist-on connectors.

5. Connect the bare ground wire from the

cooktop cable to a grounded wire in the

junction box or other grounded connector

using twist-on connector. (See Figure 3.)

Do Not connect bare ground wire to neutral

(white) wire in junction box.

junction box

white wires

twist-on

connector

black wires

U.L.- or C.S.A.- listed

conduit connector

Ungrounded neutral

Figure 3

3-wire cable from

power supply

black

wires

U.L.- or C.S.A.- listed

conduit connector

Grounded neutral

Figure 4