- ページ 4

オーブン IKEA IBD650PXS00のPDF 取付説明書をオンラインで閲覧またはダウンロードできます。IKEA IBD650PXS00 16 ページ。 30" (76.2 cm) electric single and double built-in oven

ページを印刷する

Ifcodes permit and a separate ground w ire isused, i tis

recommended

thataqualified electrical installer determine that

theground p ath and wire gauge a reinaccordance

withlocal

codes.

Check w ithaqualified electrical installer ifyouarenotsure the

oven isproperly grounded.

This oven must b econnected toagrounded metal, permanent

wiring system.

Besure that t heelectrical connection and wire size areadequate

and inconformance

withtheNational Electrical Code, ANSI/NFPA

70-latest edition o rCSA Standards C22.1-94, Canadian Electrical

Code, Part 1 and C22.2 No. O -M91-1atest

edition, and alllocal

codes a nd ordinances.

Acopy oftheabove c ode standards canbeobtained from:

National Fire Protection Association

One Batterymarch

Park

Quincy, MA02269

CSA International

8501 East P leasant Valley R oad

Cleveland, OH 44131-5575

Electrical

Connection

To properly install your oven, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

•

Oven must be connected to the proper electrical voltage and

frequency as specified on the model/serial

number rating

plate. The model/serial number rating plate is located at the

bottom of the right-hand mounting rail. See the following

illustration.

Single Oven

A. Model/serial

number plate

Double Oven

A. Model/serial

number plate

Models rated from 7.3 to 9.6 kW at 240 volts (5.5 to 7.2 kW

at 208 volts) require a separate 40-amp circuit. Models rated

at 7.2 kW and below at 240 volts (5.4 kW and below at

208 volts) require a separate 30-amp circuit.

A time-delay fuse or circuit breaker is recommended.

Connect directly to the fused disconnect

(or circuit breaker

box) through flexible, armored or nonmetallic sheathed,

copper cable (with grounding wire). See "Make Electrical

Connection"

section.

Flexible cable from the oven should be connected directly to

the junction box.

Fuse both sides of the line.

Do not cut the conduit. The length of conduit provided is for

serviceability of the oven.

A UL listed or CSA approved conduit connector must be

provided.

•

If the house has aluminum wiring follow the procedure below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors

and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's

recommended

procedure. Aluminum/copper

connection must conform with

local codes and industry accepted wiring practices.

INSTALLATIONINSTRUCTIONS

1. Decide on the final location for the oven. Locate existing

wiring to avoid drilling into or severing wiring during

installation.

Excessive Weight Hazard

Use two or more people to move and install oven.

Failure to do so can result in back or other injury.

To avoid floor damage, set the oven onto cardboard prior to

installation. Do not use handle or any portion of the front

frame for lifting.

On models with shipping feet attached:

To avoid product damage, do not remove the shipping feet at

the front lower corners of the oven. The shipping feet will

protect the lower oven trim until the oven is inserted into

cabinet.

3. Remove the shipping materials and tape from the oven.

4. Remove the hardware package from inside the bag containing

literature.

5. Remove and set aside racks and other parts from inside the

oven.

6. Move oven and cardboard close to the oven's final location.

R®

Oven T/ m

IMPORTANT." Use both hands to remove oven doors.

1. Open the oven door.

2. Locate the oven door latches in both corners of the oven door,

and rotate the latches forward to the unlocked position.

A. Oven door latch in locked

position

B. Oven door latch in unlocked

position