- ページ 6
バッテリーチャージャー MAJORCHARGE MajorCharge12/5のPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。MAJORCHARGE MajorCharge12/5 8 ページ。 Gel, pro, hd series 6/8/12/16/24/36/48 volt
ページを印刷する1. Disconnect vehicle battery cables.
2. Connect charger to battery. Ensure correct
polarity. BLACK lead to negative (-) terminal and
RED lead to POSITIVE (+) terminal.
THIS CHARGER IS PROTECTED AGAINST
REVERSE CONNECTION. CHARGING WILL NOT
COMMENCE IF BATTERY IS INCORRECTLY
CONNECTED.
3. Connect the charger to AC power supply.
THE CHARGER WILL NOW SWITCH ON AND THE
YELLOW LED WILL LIGHT.
4. The charger will now commence to charge the
battery, as indicated by the RED charging LEDs.
NOTE: The length of time the charger remains in
the "Charging Mode" depends on the size and
state of discharge of the battery. This is controlled
by the charger's solid state circuitry which
constantly monitors the state of the battery and
provides the correct charge automatically.
IMPORTANT: The charger must be allowed to go
through the complete charge routine in order to
obtain the optimum charge. This will take a
minimum of two hours.
5. When the GREEN "READY" LED comes ON, the
battery is ready for use.
NOTE: The battery may be connected to the
charger in the "READY" mode indefinitely, in
order to maintain the battery in a fully charged
state while not in use without risk of over charging.
IMPORTANT: The charger must be disconnected
from the 120 Volt power supply before
disconnecting from the battery to prevent the
possibility or arcing.
SPECIAL NOTE
6. During charging, the current flowing into the
battery is indicated by the LED Amp Meter. At the
start of charge, if the battery is normally
discharged, all 4 RED LEDs will be on and will go
out in sequence as the charge current drops.
When the last RED LED goes off, the internal
proportional timer will start, the GREEN LED will
show proportional to the time of the constant
current ime. (T/2+1hr)
7. If battery voltage is less than ½ a volt, the battery
is considered very heavily discharged. In this
case, the YELLOW charging LED will NOT show.
MajorPower.Com
1. Disconnect vehicle battery cables.
2. Connect charger to battery. Ensure correct
polarity. BLACK lead to NEGATIVE (-) terminal
and RED lead to POSITIVE (+) terminal.
THIS CHARGER IS PROTECTED AGAINST
REVERSE CONNECTION. CHARGING WILL NOT
COMMENCE IF THE BATTERY IS INCORRECTLY
CONNECTED.
3. Connect the charger to an AC Power Supply.
Check that RED (Power) and YELLOW (Charge)
indicator LEDs are ON. After a time, which
depends on how heavily the battery is discharged,
the YELLOW LED will begin to flash, indicating the
battery has reached 80% recharge level.
4. After a further time, the GREEN "READY" LED
will indicate that the battery is fully charged. The
minimum time before the GREEN "READY" LED
shows is one hour. The battery should be left on
charge until required for use.
NOTE: The length of time the charger remains in
YELLOW mode depends on the size and "State of
Charge" of the battery. This function is controlled
by the solid State Circuitry of the charger, which
provides the correct charge profile automatically.
This charger can be left safely connected to the
battery for extended periods of time.
SPECIAL NOTE
5. Batteries that have a suspect condition, particularly
"Sulfated Cells", may, when first connected,
proceed directly to the FLASHING YELLOW LED
indication. After current flow begins, the YELLOW
CHARGE LED stays ON, indicating that a normal
charge cycle is operating. This is normal operation
for the GEL charger.
The PRO & GEL chargers are fitted with a dealer-
settable BTS, which will work correctly with sealed,
gelled or flooded type batteries. Only an authorized
service technician is permitted to change the charger
battery type setting. NOTE: Failure to select correct
setting will affect the performance of the battery and
may cause battery to gas and void any warranty of the
battery. If battery type is not specified, set charger to
NORMAL mode, which will work with most battery
types. The charger is factory set in the NORMAL
mode unless otherwise specified by the original
purchaser. The BTS is NOT intended for consumer
use. If your dealer or authorized service technician is
unable to offer you this service, contact the factory for
assistance.
http://www.majorpower.com