- ページ 4

クックトップ KitchenAid KECC507KWW02のPDF 取付説明書をオンラインで閲覧またはダウンロードできます。KitchenAid KECC507KWW02 16 ページ。 36" electric built−in cooktop
KitchenAid KECC507KWW02 にも：パーツリスト (3 ページ)

ページを印刷する

Before You Make the Electrical Connection:

To properly install your cooktop, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

A 4-wire or 3-wire, single phase, 240-volt, 60-Hz., AC-only

electrical supply is required on a separate, 40-amp circuit,

fused on both sides of the line.

NOTE: The KECC051 model series requires a 20-amp circuit.

The cooktop should be connected directly to the junction box

through flexible, armored or nonmetallic sheathed, copper

cable. The flexible, armored cable extending from the fuse box

or circuit breaker box should be connected directly to the

junction box.

Locate the junction box to allow as much slack as possible

between the junction box and the cooktop so that the cooktop

can be moved if servicing becomes necessary in the future.

Do not cut the conduit. Use the length of conduit provided.

A UL listed or CSA approved conduit connector must be

provided at each end of the power supply cable (at the

cooktop and at the junction box). A listed conduit connector is

already provided at the cooktop.

If the house has aluminum wiring, connect the aluminum

wiring to the copper wire by using special connectors

designed and UL listed for joining copper to aluminum. Follow

the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

Prepare Cooktop for Installation

WARNING

Excessive Weight Hazard

Use two or more people to move and install cooktop.

Failure to do so can result in back or other injury.

1. Decide on the final location for the cooktop. Locate existing

wiring to prevent drilling into or severing wiring during

installation.

2. Using two or more people, place the cooktop upside down on

a protective surface.

3. Remove foam strip from literature packing. Remove backing

from foam strip. Apply foam strip adhesive-side down around

bottom of cooktop, flush with edge.

NOTE: The foam strip protects the underside of the cooktop

glass from debris and helps the cooktop sit flat on uneven

counters.

A. Burner box

B. Foam strip

Style 1: Cooktop over undercounter built-in oven

IMPORTANT: Clamp brackets should not be used.

1. Turn cooktop right side up.

2. Place cooktop in cutout.

NOTE: Make sure that the front edge of the cooktop is parallel

to the front edge of the countertop. If repositioning is needed,

lift entire cooktop up from cutout to prevent scratching the

countertop.

Style 2: Cooktop over cabinets

1. Determine whether your cabinet construction provides

clearance for installing clamp brackets at burner box ends.

This is the recommended location. Clamp brackets can be

installed on the front and back of burner box bottom, if

necessary.

2. The clamp brackets can be installed before or after the

cooktop is placed into the cutout. Complete the following

steps for the option you choose.

Installing Brackets Before Placing Cooktop in Cutout

1. Remove the attachment screws for the selected bracket

locations from the bottom of the burner box.

2. Select bracket mounting holes that will allow the bracket to

extend far enough out from the cooktop for the installation of

2½" (6.4 cm) clamping screws. See "Attach Cooktop to

Countertop" for illustration of clamping screw installation.

3. Attach brackets to burner box bottom with bracket

attachment screws using the bracket mounting holes selected

in Step 2.

4. Rotate brackets so they do not extend beyond edge of burner

box.

Install Cooktop

A. Attachment screw holes for optional front and back

location.

B. Clamp bracket (end locations recommended)

C. Burner box bottom

D. Attachment screw

E. Attachment screw location (recommended)

A. Edge of burner box bottom

B. Clamp bracket