- ページ 2

ペイントスプレー Green Gorilla GG025BのPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Green Gorilla GG025B 2 ページ。 Premium sprayer, non-corrosive, polyethylene, spray tank

ページを印刷する

HOW TO ASSEMBLE YOUR SPRAYER

Attach Spray Hose and Wand Handle Assembly to the Tank

(Skip this step if hose is already attached to the spray tank.)

1a. Feed the supply tube into the threaded hose port on the tank, until the o-ring

has engaged the inside of the hose port. (If necessary, apply a small amount

of liquid soap or petroleum jelly to the o-ring to aid in assembly.)

NOTE: Ensure that the o-ring does not roll up as you engage the hose port. If it

does, remove it and press back in. This should let the o-ring slide back into the

groove in the supply tube holder.

1b. Hand tighten the hose nut onto threaded hose port until snug.

NOTE: Never use tools to tighten connection nuts.

Attach Spray Wand to Wand Handle Assembly

Attach spray wand to wand handle by inserting wand into open end of handle.

Tighten the wand nut securely by hand.

NOTE: Never use tools to tighten connection nuts. DO NOT over tighten

Wand & Wand Handle Nuts. Small gaps between the nuts and the handle are

normal.

Wand Handle

O-Ring

Wand

Nut

Spray

Wand

Attach Spray Nozzle

(Skip this step if nozzle is already attached to the end of the spray wand.)

3a. Attach spray nozzle to spray wand by inserting wand into open end

of spray nozzle. Tighten the wand nut securely by hand. (Figure 3a)

NOTE: Never use tools to tighten connection nuts.

Optional: Install Spray Wand Fan Tip

Firstly, ensure that black nozzle nut is fully tightened to nozzle elbow.

3b. Unscrew red nozzle cap fully to remove and set aside. (Figure 3b)

3c. Unscrew black nozzle nut. (Figure 3c)

3d. Remove the yellow filter and red spray tip and set aside. (Figure 3d)

3e. Insert fan tip into nozzle nut, followed by the filter. (Figure 3e)

Caution: Be careful to replace the filter in the direction pictured.

3f. Hand tighten the nozzle nut back onto the wand (Figure 3f).

Nozzle

Nut

Nozzle

Cap

Figure 3b

Figure 3c

Hose

Nut

Supply

Tube

Holder

Hose

O-Ring

Port

(apply liquid soap

or petroleum jelly

to aid assembly)

Supply

Tube

Spray

Tank

Figure 1

Wand Handle

Nut

Figure 2

Nozzle

Nut

Wand

Nut

O-Ring

Nozzle

Cap

Nozzle

Elbow

Filter

Fan

Spray

Tip

Nozzle

Nut

Figure 3e

Nut

Figure 3d

Filling Your Sprayer

4a. Before every filling, first depress the manual pressure relief valve on the Easy-Twist

™

Quick-Connect

the center of the pin. (Figure 4a) Depress it firmly and hold to manually release any

pressure and then repeat several times to clear any debris and to ensure the pressure

relief valve is functioning properly.

DO NOT have your face near the Easy-Twist Quick-Connect

releasing pressure, as debris could be blown back at you.

4b. Loosen the manual pump assembly by grasping the bottom of the handle. (Figure 4b)

Once loosened, fully unscrew the manual pump assembly by the pump handle or

pump base. (You may need to press down slightly on the handle to unlock it.)

4c. Mix spray solution in separate receptacle, following manufacturers' directions

for the spray solutions.

4d. Strain solution through fine cheesecloth or household strainer to remove particles

that could clog nozzle. Use any amount of liquid up to the tank's maximum capacity

(1½ gallons or 2½ gallons depending on sprayer model). DO NOT over-fill.

4e. Replace manual pump assembly and screw it back down by the base or handle till

you feel resistance. Finish tightening the pump assembly by grasping the base of the

handle, as pictured in Figure 4b, to ensure it is snug and has made a good seal.

Ensure that the pump handle is in the locked position before carrying.

NOTE: Sprayer should only be carried by the manual pump handle (when in locked position) or with approved

accessories. Never carry tank by the hose, spray wand, or unlocked pump handle.

Pressurizing and Spraying

5a. Manually pressurize the tank by pumping until desired pressure is reached. Then, push the pump handle down

completely into the slots in the pump base and rotate the handle to the locked position (as indicated on the base). To

unlock the handle for further pumping or to remove the cap, press down slightly on the handle and rotate (as indicated

on the base).

(If optional Power Pack accessory is being used, refer to pressurization directions included with the Power Pack.)

NOTE: For proper operation, ensure that debris DOES NOT enter the

opening where the pump handle meets the pump base.

Spray

Wand

5b. Ensure that black nozzle nut is fully tightened, before adjusting nozzle cap.

Tighten cap for a fine mist spray or loosen for a coarser spray or a solid stream. (Figure 5a)

WARNING: Once a solid stream is reached, DO NOT continue loosening any further. Loosening cap

Figure 3a

too far will result in the cap falling off, allowing spray material to spray back at you.

Pressure Relief System

The Green Gorilla

(Figure 5b). The pressure relief valve is part of the Easy-Twist Quick-Connect

and will prevent the tank from becoming over pressurized. The pressure relief valve will

function with or without accessories attached to the tank.

If a hissing sound is detected through the pressure relief valve, the sprayer is over

pressurized. The pressure relief will reset automatically when the tank pressure is returned

to safe operating limits. The tank may become over pressurized by manually over pumping

or by increased pressure due to heating of the tank contents from environmental conditions.

Nozzle

NOTE: For proper operation keep pressure relief valve clean of dirt and debris.

Nut

Figure 3f

At any time, you may manually release the tank's pressure by depressing the red pin in the

center of the Easy-Twist Quick-Connect

of the Easy-Twist Quick-Connect

HOW TO USE YOUR SPRAYER

by placing your thumb on the red pin, fully covering the opening in

™

valve whenever

Premium Sprayer is equipped with a built in pressure relief valve

valve. (Figure 4a) Always keep your face clear

™

and pressure relief valve when releasing pressure.

™

Figure 4a

Pump

Handle

Pump

Base

Figure 4b

Nozzle

Nut

Nozzle

Cap

Figure 5a

system

™

Figure 5b