- ページ 7

換気フード IKEA IHW6302WM0のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。IKEA IHW6302WM0 28 ページ。 30" (76 cm), 35 7/16" (90 cm) wall-mount canopy range hood

ページを印刷する

10. Attach two mounting hooks to the wall at location marked on

the template.

...................... i ........

A. Mounting hooks

B. Centerline on wall

Vent Cover Support Bracket

Installation

Installations using telescoping

upper and lower vent cover

assembly

1. Position vent cover bracket on wall about 1/8"(3.0 mm) away

from the ceiling.

2. Mark the hole locations.

3. Drill 3/8"(9.5 mm) holes for wall anchors and insert anchors

flush with the wall.

e-.. e _::D ................

A. 10.0 x 60.0 mm drywall anchors

B. Centerline on wall

C. Vent cover support bracket

D. 6.0 x 70.0 mm screws

4. Attach vent cover support bracket to wall.

Installation

locations

with reduced

ceiling heights

NOTE: Either the lower or the upper vent cover can be used for

such installation but note that upper vent cover is smaller than

the lower vent cover. There will be more clearance were the upper

vent cover attaches on top of the range hood.

For non-vented (recirculating) installations:

The vent hood is installed using the upper vent cover

(26" [66.0 cm]) plus a %" (10.0 mm) thick wood filler.

1. For the vent cover to slide down and engage the top of the

hood, the vent cover bracket must be installed 2/8"(10.0 mm)

below the ceiling.

2. The remaining space above the vent cover can be filled with a

2/8"(10.0 mm) thick piece of plywood cut to the inside cross

section of the chimney cover and finished to match the

ceiling.

For vented installations:

The vent hood is installed using the lower vent cover

(163/4"[42.5 cm]) plus a 2/8"(10.0 mm) thick wood filler.

1. For the vent cover to slide down and engage the top of the

hood, the vent cover bracket must be installed 2/8"(10.0 mm)

below the ceiling.

2. The remaining space above the vent cover can be filled with a

2/8"(10.0 mm) thick piece of plywood cut to the inside cross

section of the chimney cover and finished to match the

ceiling.

Cut the self adhesive rubber tape supplied with the hood in 4

identical pieces. Attach 2 pieces of tape to each side of the

support bracket.

..................................

A. Vent cover bracket

B. Rubber tape

Vented Installations

Install transition on top of hood (if removed for shipping) with

2 sheet metal screws.

Non-Vented (recirculating) Installations

1. Install transition on top of hood (if removed for shipping) with

2 sheet metal screws.

2. Attach the vent cover ceiling bracket to the deflector with the

two 3.5 x 9.5 mm screws provided.

A. Vent cover bracket

B. 3.5 x 9.5 mm screws

C. Deflector

3. Connect the deflector to the transition with 6" (15.2 cm)

round vent once hood has been set in place.

Complete

Preparation

1. Determine and make all necessary cuts in the wall for the vent

system. Install the vent system before installing the hood. See

"Venting Requirements"

section.

2. Determine the required height for the 1/2"conduit and drill a

1V4" (3.2 cm) hole at this location.

3. Run wire through the 1/2"conduit according to the National

Electrical Code or CSA Standards and local codes and

ordinances. There must be enough 1/2"conduit and wires from

the fused disconnect

(or circuit breaker) box to make the

connection

in the hood's electrical terminal box.

NOTE: Do not reconnect power until installation is complete.

4. Use caulk to seal all openings.