- ページ 6

換気フード IKEA IHW6362VM0のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。IKEA IHW6362VM0 28 ページ。 30" (76 cm), 35 7/16" (90 cm) wall-mount canopy range hood

ページを印刷する

Observe allgoverning codes a ndordinances.

Ensure thattheelectrical installation isadequate and in

conformance

withNational Electrical Code, ANSI/NFPA

70(latest

edition), orCSA Standards C22.1-94, Canadian Electrical Code,

Part 1 andC22.2 No. 0 -M91 (latest edition) andalllocal c odes

andordinances.

Ifcodes permit and a separate ground w ire isused, i tis

recommended

thataqualified electrician determine thatthe

ground p athisadequate.

Acopyoftheabove c ode standards canbeobtained from:

National Fire Protection Association

One Batterymarch

Park

Quincy, MA02269

CSA International

8501 East P leasant Valley R oad

Cleveland, OH 44131-5575

•

A 120 Volt, 60 Hz., AC only, 15-amp, fused electrical circuit is

required.

•

If the house has aluminum wiring follow the procedure below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors

and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's

recommended

procedure. Aluminum/copper

connection must conform with

local codes and industry accepted wiring practices.

•

Wire sizes and connections

must conform with the rating of

the appliance as specified on the model/serial

rating plate.

The model/serial

plate is located behind the filter on the rear

wall of the hood.

Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA

Standards C22.1-94,

Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

INSTALLATION INSTRUCTIONS

•

Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

•

Check your ceiling height and the hood height maximum

before you select your hood.

1. Disconnect

power.

2. Determine which venting method to use: roof, wall, or non-

vented.

3. Select a flat surface for assembling the range hood. Place

covering over that surface.

It is recommended

that the vent system be installed before

7. Tape template in place, aligning the template centerline and

hood is installed,

bottom of template with hood bottom line and with the

centerline marked on the wall.

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

A. Centerline

B. Mounting hook location

C. Fastener locations

D. Mounting height reference

4. Using 2 or more people, lift range hood onto covered surface.

Range Hood Mounting Screws Installation

Determine and mark the centerline on the wall where the

canopy hood will be installed.

Select a mounting height between a minimum of

30" (76.2 cm) and a suggested maximum of 36" (91.4 cm),

above the range to the bottom of the hood and mark

reference line on the wall.

NOTE: For installation locations with reduced ceilings

heights, the vent hood may be installed using the upper vent

cover for both vented and non-vented

(recirculating)

installations.

8. Mark centers of the 6 fastener locations through the template

to the wall.

IMPORTANT: All screws must be installed into wood.

Remove the template.

9. Drill %4" (2.75 mm) pilot holes at all locations where screws

are being installed into wood.