- ページ 2

食器洗い機 KitchenAid KD-19 SeriesのPDF 設置方法をオンラインで閲覧またはダウンロードできます。KitchenAid KD-19 Series 5 ページ。 Built-in dishwasher

ページを印刷する

~w~RTANT:

Read Before

Installing

to Save

Time,

Work,

assure

proper

parfatmance,

and owner's

warranty

protection.

KDJKA INSTALLATION

KIT

installation

kit (KD-IKA)

for KltchonAid

dishwashers is available from your local KitchenAid dealer. This

kit

\) oontains

all parts end complete

instruotiorU needed for replacing almost any old dishwasher,

for a new dish-

' washor installation.

The KD-IKA installation kit includes the following items:

Flexible Drain Hose, Copper Inlet Tubing, Double Corn-ion

Union, Double Com-

pression Elbow, Step-down Adapter, Strain Relief Bushing, Wire Nuts, and

Hose

Clamps.

CABINETRY

Opening for dishwasher should

be 24" wide- by

approximately

34-l/2"

high. Remove all obstructrons

at the upper rear of ttm opening-see Step 1 below.

ELECTRICAL

SPECIFICATIONS

Voltage 81 Fraquew

115 volts-60

hertz

operatiw

Iad

13.5 amperes

Maximum Fuse Sire

16 amp*

Wiring must conform

to local oode and/or

Nat.

Electrical Code.

PLUMBING

SPECIFICATIONS

Plumbing

must conform

to local code.

Use l/2" 0.0.

copper tuba for water line. Dishwasher has 3/8" I.P.S.

internal

thread at valve. A 86"

compression

eil

(furnished) should be used to connect tubing to valve.

Water flow pressure at dlshwasher to be 20 PSI to

120 PSI. Watar temperature at dishwasher should be

120' F. or higher. Drain size requires minimum 5/8"

0.0.

copper tubing

without

air gap. Drain llnr

requires min. a/16" I.D. mpper tubing with air gap,

not furnished.

CAUTION:

Avoid getting joint compound insido

new joink.

Hot water fill

line must be flushed

foreign

mafter

before connection

to dis@vasher fill

valve. A

hand shut off valve

(not furnished) should be

located in an easily aooassible area adjacent to the

dish-her.

INSTALLATION

INSTRUCTIONS

Locate top of lower panel just below evaporation channel support.

Insert panel flange under evaporation ohannel support ends "A'

and

push up to

ongage top

of panel. Lift up lower bottom ?anga of

panel,

plaa

flange "B" over front face of frame and push in. &semble

lock

washer "0"

under head of one screw to ground panel to dishwasher.

Fasten panel with- two scrawE

"C"

furnished.

wood or laminate

. .

'&R----- /"

front

is to be used and those Panels are not immediately

available,

use

---J-

tadeup

panel

furnished

with

trim kit

Stainless steel trim should

FIG. 1

used

to assemble wood or laminate when avallable. Revene procedure

when removing lower panel.

PRELIMINARY

ROUGH-IN

CABINET

OPENING

For

dishwasher

to be flush with adjacent cabinets, there must be a minimum

of 24" under counter cabinet depth available for installation.

When a 114"

wood

panel

(lower

front

panel, 6-s/8"

hi&,

231 l/16"

wick% door front

panel, 187/6"

high, 23-11/16"

wide)

with

trim

kit is used the dishwasher

must have minimum

of 24-l/4"

cabinet

&@I.

To establish

a reference line

for

purmSeS

providing

plumbing

electtiUl

WnnMtiOllS

th0

dishwasher,

mewrrre 21"

from

the wall. (This is the front edge of dishwasher

kick panel. There is a 3" toe

tpm

from the front

of the kick panel to the

from

edge

the dishwasher

with

a standard

metal front

panel.1 Cabinets

73-l/2"

235/W

deep from wall to front

of cabinet

may b aaxmmo-

.ted by removing

dry or ~larter wall, baaboard

and quartir

round dira3ly

ind tI-:

?ishfrwssher,

NOTE:

- fcmer

installation,

allow

2" clearance for adjacent cabinet

CAUTIC

Make sure dishwasher is not installed

under a surface

burner or

warmins

:iate

where

the

heat

would

damage

the

water

supply

tubing.

FIG.