- ページ 12

食器洗い機 KitchenAid KIO 3T133 PFE UKのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。KitchenAid KIO 3T133 PFE UK 16 ページ。

Care and maintenance

ATTENTION: Always unplug the appliance when cleaning it and when performing maintenance work. Do not use flammable liquids to clean

the machine.

CLEANING THE DISHWASHER

Any marks on the inside of the appliance may

be removed using a cloth dampened with water

and a little vinegar.

The external surfaces of the machine and the control

panel can be cleaned using a non-abrasive cloth

which has been dampened with water. Do not use

solvents or abrasive products.

PREVENTING UNPLEASANT ODOURS

Always keep the door of the appliance ajar in order to avoid moisture

from forming and being trapped inside the machine.

Clean the seals around the door and detergent dispensers regularly

using a damp sponge. This will avoid food becoming trapped in the seals,

which is the main cause behind the formation of unpleasant odours.

CHEKING THE WATER SUPPLY HOSE

Check the inlet hose regularly for brittleness and cracks. If damaged,

replace it by a new hose available through our After-Sales Service

or your specialist dealer. Depending on the hose type:

If the inlet hose has a transparent coating, periodically check

if the colour intensifies locally. If yes, the hose may have a leak

and should be replaced.

For water stop hoses: check the small safety valve inspection

window (see arrow). If it is red, the water stop function was triggered,

and the hose must be replaced by a new one.

For unscrewing this hose, press the release button while unscrewing

the hose.

CLEANING THE WATER INLET HOSE

If the water hoses are new or have not been used for an extended period

of time, let the water run to make sure it is clear and free of impurities

before performing the necessary connections. If this precaution

is not taken, the water inlet could become blocked and damage

the dishwasher.

CLEANING THE FILTER ASSEMBLY

Regularly clean the filter assembly so that the filters do not clog

and that the waste water flows away correctly.

Using dishwasher with clogged filters or foreign objects inside filtration

system or sprayarms may cause unit malfunction resulting in lose

of performance, noisy work or higher resources usage.

The filter assembly consists of three filters which remove food residues

from the washing water and then recirculate the water.

The dishwasher must not be used without filters or if the filter is

loose.

At least once per month or after each 30 cycles, check the filter assembly

and if necessary clean it thoroughly under running water, using a non-

metallic brush and following the instructions below:

1. Turn the cylindrical filter A in an anti-clockwise direction and pull

it out (Fig 1).

2. Remove the cup filter B by exerting a slight pressure on the side

flaps (Fig 2).

3. Slide out the stainless-steel plate filter C (Fig 3).

4. In case you find foreign objects (such as broken glass, porcelain,

bones, fruit seeds etc.) please remove them carefully.

5. Inspect the trap and remove any food residues. NEVER REMOVE

the wash-cycle pump protection (black detail) (Fig 4).

After cleaning the filters, re-place the filter assembly and fix it in position

correctly; this is essential for maintaining the efficient operation

of the dishwasher.

CLEANING THE SPRAY ARMS

On occasions, food residue may

become encrusted onto the spray

arms and block the holes used to spray

the water. It is therefore recommended

that you check the arms from time

to time and clean them with a small

non-metallic brush.

To remove the upper spray arm, turn

the plastic locking ring in an anti-

clockwise direction. The upper spray

arm should be replaced so that the side

with the greater number of holes is

facing upwards.

The lower spray arm may be removed

by pulling it upwards.