- ページ 10

食器洗い機 KitchenAid KUDC10IXSS7のPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。KitchenAid KUDC10IXSS7 18 ページ。

ページを印刷する

CONTROL

PURPOSE

COMMENTS

To start or iesume a

If the door is opened during a cycle orthe power is interrupted, the StartJResUme indicator

wash cycle

flashes. The cycle will not resume until the door is closed and START/RESUME is pressed.

"°:_!t°t'!_°'?

NOTE: If the Start!Resume

button is located on top of door, push door f rm!y closed within

3 seconds of pressing START/RESUME. !f the door is not closed within 3 seconds, the

StartJResume butt0n LED wi!l flash, an audible tone wi! I be heard, and the cYCle wi!l not

start.

To reset any cycle or

options during

selection.

To cancel a wash

cycle after it's

started.

Press and hold CANCEL/DRAIN to reset any control selections made.

See "Canceling A Cycle After Dishwasher Is Started" and "Changing A Cycle After

Dishwasher Is Started" sections.

To turn the audible

Press and hold the Hi-Temp scrub button for3 Seconds t0 turn the audible tones on or off.

tones on croft.

Only audible tones for confirming button presses can be turned 0n/off. Important audible

_or!',Q!/°":,:!

tones, such as indicating a cycle has been interrupted,

cannot be deactivated.

£ ee(i;tI,}acl_+{be(it_ () s

CONTROL

PURPOSE

COMMENTS

w:ii:i i i:_ c:il iil i:i

The Cycle Status Indicator

Clean indicator glows When a cycle is finished.

•

Lghtsareusedtofo

owthe

. .

°,

,..

If y0u select the Sani Rinse optlon, when the Sanl R_nsecycle!sflnlshed,

progress of IRe alsnwasner

, ,

_ ,

_. :

the Sanitized indicator g!ows, lf y0ur dishwasher did not proper!y sanitize

cycle Locatecl on me Tront

of the d s[qwasher for front

your dishes, the light flashes at the end of the cYClel This can happen if the

. ,

;

cycle is interrupted

or the water could not be heated to the required

contro moaes

ann ocatea

tem er t r

....

......................................

on the top of the do0r for

hidden control models.

The Clean and Sanitized lights go off when you open and close the door or

)ress and hold CANCEL.

The Front Indicator Light or

Single Exterior Light (A)

shows progress of your

dishwasher cycle by color.

(Available on some hidden

control models only).

The light will be blue if the dishwasher is washing or rinsing. The light will

be red when the dishwasher is drying. The light will be green to indicate

that the cycle is complete. If the Front Indicator Light is blinking, see

"Troubleshooting"

section.

The Cycle Status Display is

The indicators Wi!l inform you if you are able to add a dish to the Cycle after

•

: _

.....

used to follow the progress

it has started. It wi!! a!so inform you if the dishwasher is washing rinsing

;.. :

u .....

'" '

of the dishwasher cycle, and drying,

complete, and/or sanitized. They will show whether the control is

to show other nformation,

locked and!or the delay option is selected. A series of bars will count down

(Availab!e on some models

the duration of the cycle remaining from left to right, Each bar equa!s

instead of Cycle Status

approximately

24 minutes of cycle lengthi The bars will also count down

Indicator Lights)the

delay feature from left to right, and the de!ay indicator will be activated.

Canceling

A Cycle

1. Press and hold the Cancel/Drain

button once. The Cancel/

Drain light will turn on. If the Cancel/Drain button is located on

the top of the door, open the door slightly to stop the cycle.

Wait for the spraying action to stop before completely opening

the door. Press and hold the Cancel/Drain

button once.

Close the door and the dishwasher starts a drain cycle (if water

remains in bottom of dishwasher). Let the dishwasher

drain

completely. The Cancel/Drain

light turns off after 2 minutes.

Changing

A Cycle

After

Dishwasher

Is Started

1. You can interrupt a cycle and restart your dishwasher from the

beginning using the following procedure.

Press and hold the Cancel/Drain

button twice to reset the

control. If the Cancel/Drain

button is located on the top of the

door, open the door slightly to stop the cycle. Wait for the

spraying action to stop before completely

opening the door.

Press and hold the Cancel/Drain

button twice to reset the

control.

3. Select new cycles and options.

4. Press START/RESUME.

Adding

A Dish After

Dishwasher

Is Started

1. Check if Add a Dish indicator is lit. (Available on some models.

Otherwise, proceed to Step 2.)

2. Open the door slightly to stop the cycle. Wait for the spraying

action to stop, then open the door completely.

3. Check whether the detergent dispenser cover is still closed. If

it is open, the wash cycle has already started and adding a

dish is not recommended.

4. If detergent has not yet been used (detergent dispenser cover

is closed), you may add a dish.

5. Press START/RESUME.