ページを印刷するHow much detergent
to use
•
The amount of detergent to use depends on the hardness of
your water and the type of detergent. If you use too little,
dishes won't be clean. If you use too much in soft water,
glassware will etch.
•
Water hardness can change over a period of time. Find out
your water's hardness by asking your local water department,
water softener company, or county extension agent.
Where to fill
Top of 3rd step (9 tsp or 45 mL)
Top of 2nd step (6 tsp or 30 mL)
Top of 1st step (3 tsp or 15 mL)
Soft to Medium Water (0-6 grains per U.S. gallon)
[typical water softener water and some city water]
Soil Level
Main Wash
Pre-Wash
Lightly soiled/Pre-
3 tsp (15 mL)
3 tsp (15 mL)
rinsed dish loads
[top of 1st step]
[top of 1st step]
Normally soiled
6 tsp (30 mL)
6 tsp (30 mL)
dish loads
[top of 2nd step]
[top of 2nd step]
Heavily soiled
9 tsp (45 mL)
6 tsp (30 mL)
dish loads
[top of 3rd step]
[top of 2nd step]
Medium to Hard Water (7-12 grains per U.S. gallon)
[well water and some city water]
Soil Level
Main Wash
Pre-Wash
All soil types
9 tsp (45 mL)
6 tsp (30 mL)
[top of 3rd step]
[top of 2nd step]
NOTE: Fill amounts shown are for standard powdered detergent.
Amounts may vary if you use liquid or concentrated
powdered
detergent. Tablet detergents should be placed in the main wash
section of the detergent dispenser with the cover closed. Follow
instructions
on the package when using liquid dishwasher
detergent, concentrated
powdered detergent or tablet detergent.
IMPORTANT: See "Cycle Selection Charts" for which detergent
dispenser sections to use with each cycle.
Rinse aids keep water from forming droplets that can dry as
spots or streaks. They also improve drying by allowing water to
drain off of the dishes during the final rinse by releasing a small
amount of the rinse aid into the rinse water. Your dishwasher
is
designed to use a liquid rinse aid. Do not use a solid or bar-type
rinse aid.
Checking the dispenser
Check the center of the fill indicator cap. Clear means it needs
filling.
Or you can remove the fill indicator cap. If an "E" is visible, the
dispenser is empty.
Filling the dispenser
The rinse aid dispenser holds 6 oz (175 mL) of rinse aid. Under
normal conditions,
this will last for about 3 months. You do not
have to wait until the dispenser is empty to refill it. Try to keep it
full, but be sure not to overfill it.
1. Make sure the dishwasher door is completely open.
2. Remove the fill indicator cap.
3. Add rinse aid. Fill to the smallest opening in the lower part of
the dispenser. Overfilling can cause the rinse aid to leak out,
and could cause oversudsing.
4. Clean up any spilled rinse aid with a damp cloth.
5. Replace the fill indicator cap. Close tightly.
Hot water dissolves and activates the dishwashing detergent.
Hot water also dissolves grease on dishes and helps glasses dry
spot-free. For best dishwashing
results, water should be 120°F
(49°C) as it enters the dishwasher. Loads may not wash as well if
the water temperature
is too low. Water that is too hot can make
some soils harder to remove and cause certain detergent
ingredients not to function. If your water heater is located far from
the dishwasher, it may be necessary to run the hot water at the
faucet closest to the dishwasher to minimize the amount of cold
water in the water line. The benefits of minimizing the amount of
cold water in the water line cannot be achieved if the Delay Wash
option is chosen.