- ページ 4

防犯カメラ ALIBI ali-bc1080eのPDF クイック・インストール・マニュアルをオンラインで閲覧またはダウンロードできます。ALIBI ali-bc1080e 4 ページ。 Hd-tvi outdoor infrared bullet camera

ページを印刷する

Click the q or p button to position the > marker at either SAVE/EXIT or EXIT, and then click the

Iris + button.

SAVE/EXIT: Use this option if you want to retain the setting. It can be changed at any time.

EXIT: Use this option if you want to retain the setting temporarily. If the camera is powered off, the

NOTE

new setting is lost.

Example 2: Change the camera video settings

Video settings for the camera are configured in the EFFECT submenu. You an also flip (vertical reflection)

and/or mirror (horizontal reflection) the image in this menu. To change the setting:

Open the OSD Main Menu (see "Step 3. Open the OSD menu" on page 2).

Click the q button to position the > marker at EFFECT, and then click the Iris + button to open the

EFFECT submenu.

Click the q or p button to position the > marker at the parameter you want to change, and then

click the t or u button to decrease or increase the setting. The FLIP and RETURN options are

either ON or OFF. The effect of changing the parameter is shown immediately in the video image.

Repeat the previous step to change other parameter values if necessary.

Click the q button to position the > marker at RETURN, and then click the Iris + button to return

to the previous menu (MAIN MENU).

Click the q button to position the > marker at EXIT, and then click the Iris + button to open the

EXIT submenu.

Click the q or p button to position the > marker at either SAVE/EXIT or EXIT, and then click the

Iris + button.

Cleaning

Clean the camera dome with an approved glass cleaning solution and a lint free cloth.

Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub

•

the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a

soft cloth.

Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing.

•

These may cause damage to the surface over time.

Do not use benzene, thinner or other chemical products on the camera assembly; these may



dissolve the paint and promote damage of the surfaces. Before using any chemical product,

CAUTION

carefully follow the accompanying instructions.

www.observint.com

Specifications

Model

ALI-BC1080E

Camera

Image Sensor

1 / 2.7" Progressive Scan CMOS

Signal System

NTSC

Effective Pixels

1930(H) * 1088(V)

Min. Illumination

0.1 lux @ (F1.2, AGC ON), 0 lux with IR

Shutter speed

1/30 s to 1/50,000 s

Lens

3.6 mm lens, angle of View: 90°

Lens Mount

M12

Day & Night

ICR

Synchronization

Internal synchronization

Video Frame Rate

1080p @ 30 fps

HD Video Output

1 Analog HD output

S / N Ratio

More than 52 dB

Camera ID

On/off (0 ~ 255)

AGC

Support

D/N Mode

Color / BW/ Auto / EXT

White Balance

Auto / User / Push / 8000 K / 6000 K / 4200 K / 3000 K

Privacy Mask

On/Off, maximum 2 zones

Motion Detection

On/Off, maximum 4 zones

BLC

Support

Anti-flicker

On / Off

Language

English / Chinese

Function

Digital noise reduction, Mirror

General

Working Temperature / Humidity

14 °F ~ 122 °F (-10 °C ~ 50 °C)

Humidity

90% or less (non-condensing)

Power Supply

12 Vdc

Power Consumption

Max. 3W

Weather Proof Ratings

IP66

IR Range

Up to 65 ft (20 m)

Communication

Up the coax (OSD control through the HD-TVI DVR)

Protocol:

Coaxitron

Dimensions

Φ2.76" × 5.89" (Φ70 × 149.5 mm)

Weight

0.79 lbs (360 g)

Troubleshooting

Problem

Nothing appears on the screen

The video image is dim or not clear.

The screen is dark.

The camera is not working properly and the

surface of the camera is hot.

The image on the monitor flickers

Possible Cause

- Check the power connection.

- Check the video signal cable connection to the monitor.

- If the camera lens is dirty, clean it with a soft, clean cloth.

- Adjust the monitor controls, if necessary.

- If the camera is facing a very strong light, change the camera position.

- Adjust the lens focus.

- Adjust the contrast control of the monitor.

- If you have an intermediate device, set the impedance (75 Ω /Hi-Z)

properly, and check the cable connections.

- Verify that the camera is correctly connected to an appropriate regulated

power source.

- Make sure that the camera isn't facing direct sunlight or fluorescent light.

If necessary,change the camera position.