- ページ 7

電動工具 Makita 0088381640978のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Makita 0088381640978 17 ページ。 Cordless plate joiner

ページを印刷する

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CARTRIDGE

Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using bat-

tery.

Do not disassemble battery cartridge.

If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

Do not short the battery cartridge:

(1) Do not touch the terminals with any conduc-

tive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a break-

down.

Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

Do not incinerate the battery cartridge even if it

is severely damaged or is completely worn out.

The battery cartridge can explode in a fire.

Be careful not to drop or strike battery.

Do not use a damaged battery.

SAVE THESE INSTRUCTIONS.

Adjusting the depth of groove (Fig. 2)

6 grooving depths can be preset according to the size of biscuit to be used.

Refer to the table below for the correspondence between the sizes marked on the stopper and the biscuit size. Fine

adjustments to the grooving depth can be made by turning the adjusting screw after loosening the hex nut. This may

become necessary after the blade has been resharpened a few times.

Size on stopper

Biscuit size

Depth of groove

* With the rubber spikes removed.

012681

Angle guide (Fig. 3 & 4)

The angle guide height can be moved up and down to

adjust the position of the blade in relation to the top of the

workpiece.

To adjust the angle guide height, loosen the lock lever

down and rotate the knob until the pointer points to the

desired scale graduation marked on the angle guide.

Then tighten the lock lever up to secure the angle guide.

The scale on the angle guide indicates the distance from

the top of the workpiece to the center of the blade thick-

ness.

The angle guide is removable from the fence according

to the need of your work. To remove the angle guide,

loosen the lock lever and turn the knob clockwise until it

comes out of the upper end of the fence.

ENC007-7

8 mm

10 mm

Tips for maintaining maximum battery life

Charge the battery cartridge before completely

discharged.

Always stop tool operation and charge the bat-

tery cartridge when you notice less tool power.

Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

Charge the battery cartridge with room tempera-

ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-

tery cartridge cool down before charging it.

Charge the battery cartridge once in every six

months if you do not use it for a long period of

time.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before adjusting or checking

function on the tool.

Installing or removing battery cartridge (Fig. 1)

• Always switch off the tool before installing or removing

of the battery cartridge.

• To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

• To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If you can see the red indicator

on the upper side of the button, it is not locked com-

pletely. Install it fully until the red indicator cannot be

seen. If not, it may accidentally fall out of the tool, caus-

ing injury to you or someone around you.

• Do not use force when installing the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

—

12.3 mm

13 mm

Fence (Fig. 5 & 6)

NOTE:

• Remove the angle guide according to the need of your

work when using the tool with the angle of the fence

adjusted to other than 0°. When you need to use the

angle guide under the above condition, be sure to

adjust the depth of groove to get a proper depth.

MAX

—

14.7 mm

20 mm*