- ページ 2

DVR ALIBI ALI-HVR5016HのPDF クイック・セットアップ・マニュアルをオンラインで閲覧またはダウンロードできます。ALIBI ALI-HVR5016H 9 ページ。 16-channel hd-tvi digital video recorder

ページを印刷する

Item

Description

CVBS - BNC connector for video output

VGA - DB15 connector for VGA compatible monitor. Supports 1920 × 1080 @ 60 Hz, 1280 × 1024 @ 60 Hz,

VIDEO OUT

1280 × 720 @ 60 Hz/, 1024 × 768 @ 60 Hz

(CVBS, VGA, HDMI)

HDMI - HDMI connector for an HDMI compatible monitor. Supports 1920 × 1080 @ 60 Hz, 1280 × 1024 @ 60 Hz,

1280 × 720 @ 60 Hz/, 1024 × 768 @ 60 HzH

LINE IN

RCA connector for audio input

RS-485, ALARMS IN/OUT

See below, next topic

Power connector

AC 100V ~ 240V power supply.

ON / OFF Switch

Switch for powering the device on or off

GROUND

Terminal for ground. Connect to earth ground before powering on the DVR.

LAN Interface

10/100/1000BASE-T Ethernet network interface

USB interface

Universal Serial Bus (USB) ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD).

CVBS AUDIO OUT - BNC connector for audio output. This connector is synchronized with CVBS video output

AUDIO OUT

VGA AUDIO OUT - BNC connector for audio output. This connector is synchronized with VGA video output

HD-TVI video inputs

HD-TVI interface for video input

RS-485, ALARMS IN/OUT

Item

Description

RS-485 (T+, T-, R+. R-)

T+ and T- pins connect to R+ and R- pins of PTZ receiver respectively.

Controller port:

D+, D- pin connects to Ta, Tb pin of controller.

For cascading devices, the first DVR's D+, D- pin should be connected with the D+, D- pin of the next DVR

Alarm inputs 1 - 16. Alarm input is tied to ground through the alarm sensor. See

ALARM IN (1 through 16)

for more information.

ALARM OUT

Alarm outputs 1 - 4 with ground terminations. See

(1-G through 4-G)

www.Observint.com

"Step 1. Connecting alarm devices to the DVR" on page

"Step 1. Connecting alarm devices to the DVR" on page 3

for more information.

1.1.1 Remote control

The enter key on the remote control or the front panel has the same function as a mouse left click. The IR Range of the remote control is 10

meters. The buttons on the remote control correspond with the buttons on the front panel.

Item

Name

Function

POWER

Power on/off the device.

DEV

Enables/Disables Remote Control.

Alphanumeric Buttons

Use for entering numerical data

Delete characters before cursor, check the checkbox and select the ON/OFF switch, start/stop record clipping in

EDIT Button

playback

Adjust focus in the PTZ Control menu, also used to switch between input methods (upper and lowercase alphabet,

A Button

symbols and numeric input).

REC Button

Open the manual record interface

PLAY Button

Playback, for direct access to playback interface.

INFO Button

Reserved.

VOIP/MON button

Switch between main and spot output. In PTZ Control mode, it is used to zoom out the image.

Press the button will help you return to the Main menu (after successful login).

MENU button

Press and hold the button for 5 seconds to turn off audible key beep.

In PTZ Control mode, the MENU/WIPER button will start wiper (if applicable).

Switch between single screen and multi-screen mode.

PREV button

In PTZ Control mode, it is used to adjust the focus in conjunction with the A/FOCUS+ button.

DIRECTION: These buttons are used to navigate between different fields and items in menus.

In the Playback mode, the Up and Down buttons are used to speed up and slow down recorded video. The Left and

Right button select the next and previous record files.

In Live View mode, these buttons can be used to cycle through channels.

In PTZ control mode, they can control the movement of the PTZ camera.

DIRECTION/ENTER buttons

ENTER: The ENTER button is used to confirm selection in any of the menu modes.

It can also be used to tick checkbox fields.

In Playback mode, it can be used to play or pause the video.

In single-frame Playback mode, pressing the button will advance the video by a single frame.

In Auto-switch mode, it can be used to stop /start auto switch.

Enter the PTZ Control mode (if applicable).

PTZ button

In the PTZ Control mode, it is used to adjust the iris of the PTZ camera.

Return to the previous menu.

ESC button

Press for Arming/disarming the device in Live View mode.

RESERVED

Reserved for future usage.