- ページ 2

レンジ KitchenAid YKGRC608LS0のPDF 取付説明書をオンラインで閲覧またはダウンロードできます。KitchenAid YKGRC608LS0 7 ページ。 30" freestanding and slide-in sealed burner gas range with self-cleaning oven

KitchenAid YKGRC608LS0 取付説明書
Before
you start...
Your safety and the safety of others
are very important.
We have provided many important safety messages in
this manuaIand on your appliance. Always read and
obey all safety messages.
This is the safety aIert symb0i.
This symb0t aierts you to potential hazards
that can kiii or hurt you and others.
Ati safety messageswiii f0ii0w the safety alert symbol
and either the word "DANGER"or "WARNING". These
words mean:
You can be killed or sed0usly injured if you don't
f0H0w instructions.
AII safety messageswilI teli you what the p0tentiai
hazard is, teli you how to reduce the chance of injury,
and teii you what can happen if the instructions are not
followed.
WARNING:
_f the information
in this
manual
is not followed
exactmy, a fire
or expmosion
may resuJt causing
property
damage,
personal
injury
or
death.
- Do not store
or use gasoline
or
other flammabme
vapors
and miquids in
the vicinity
of this or any other
appliance.
-WHAT
TO DO iF YOU SMELL
GAS
o Do not try to _ight any appliance.
o Do not touch
any e_ectrica_ switch
o Do not use any phone
in your
building.
o Immediately
call your
gas supplier
from
a neighbor's
phone.
Follow
the
gas supplier's
instructions.
o if you cannot
reach your
gas
supplier,
call the fire department.
- Installation
and service
must
be
performed
by a qualified
instalmer,
service
agency
or the gas supplier.
Countertop opening dimensions that are shown
must be used. Given dimensions provide required
clearances.
To eliminate the risk of burns or fire by reaching
over heated surface units, cabinet storage space
located above the surface units should be avoided.
If cabinet storage is to be provided, the risk can be
reduced by installing a range hood that projects
horizontally a minimum of 5 inches beyond the
bottom of the cabinets.
Read electrical and carpentry instructions.
Proper installation is your responsibility. A qualified
technician must install this range. Make sure you
have everything necessary for correct installation. It
is the customer's responsibility to make sure that
the countertop has been properly prepared and that
the installation clearances specified on the
model/serial rating plate are met. The model/serial
rating plate is located on the oven frame behind the
oven drawer.
Check location where range will be installed. The
range should be located for convenient use in the
kitchen. Recessed installations must provide
complete enclosure of the sides and rear of range.
All openings in the wall or floor where range is to be
installed must be sealed.
IMPORTANT: Some cabinet and building materials
are not designed to withstand the heat produced by
the oven for baking and self-cleaning. Check with
your builder or cabinet supplier to make sure that
the materials used will not discolor, delaminate or
sustain other damage.
It is the customer's responsibility:
To contact a qualified electrical installer.
Panel A
Cabinet
opening
dimensions
25" (63.5 cm) countertop
depth (with or without
backsplash)
and 24" (61 cm) base cabinet
depth, 36" (91.4 cm) countertop
height
Freestanding
"_ _3" (33 cm) max.
pper cabinet depth j
_,_j.
18" (45.7 cm)
For minimum
upper side cabinet
30" (76.2 cm) cabinet
clearance to
to countertop
///_...._
opening w_dth
cooktop, see
***Note
30" (76.2 cm)
(7.3,,cm_.t.._,_
opening width
(22.9 cm)
4" (10.2 cm) min. clearance
from both sides of range to
side wall or other
combustible
material.
!
(I5.2 cm)
Gas line opening can be
located within this
area.
2" (5.1 cm)__
(25.4 cm) Outlet should be
located within the 18" x
10" (45.7 cmx 25.4 cm)
shaded area. 1
2-1/2" (6.4 cm)
1
floor gas line
"_\
_h._//
opening if directly
_
I -
/
below regulator
7/8" (2.2 cm) min.
required between
cabinet opening
and door or hinge
opening.
4 (10 2 cm) mln
other combustible
mater_i
--\
_//
(22.9 cm)
3 _
(7.6 cm)
Gas line opening should
be located within this
shaded area.
floor gas line opening if
directly below regulator
30" (76.2 cm)
opening width
(15.
(61 cm)
Outlet should be
located within
the 18" x 10"
(45.7 x 25.4 cm)
shaded area.
IMPORTANT:
Rear vent must be
installed on all slide-in
models for proper
ventilation. See Step 7,
Panel D.
7/8" (2.2 cm) min. required between
pening and door or hinge
opening.
To assure that the electrical installation is adequate
and in conformance with National Electrical Code,
ANSI/NFPA 70 -- latest edition*, or CSA Standard
C22.1, Canadian Electrical Code, Part 1 --latest
edition**, and all local codes and ordinances.
NOTE: This appliance is manufactured for use with
Natural Gas. Conversion to LR Gas can be made
using the kit included in your literature package.
NOTE: The metal chassis of the range must be
grounded in order for the control panel to work. If
the metal chassis of the range is not grounded, no
keypads will operate. Check with a qualified
electrician if you are not sure the range is
grounded.
IMPORTANT: Observe all governing codes and
ordinances.
Grounded electrical outlet is required. See
"Electrical requirements," Panel C.
Cabinet opening dimensions that are shown must
be used.
Do not pinch the power supply cord between the
range and the wall.
Do not seal range to side cabinets.
Copies of the standards listed may be obtained from:
*National Fire Protection Association
One Batterymarch
Park
Quincy, Massachusetts
02269
** CSA International
8501 East Pleasant'Valley
Road
Cleveland, Ohio 44131-5575
*** NOTE: 24" (61 cm) min. when bottom of wood or
metal cabinet is protected by not less than 1/4"
(6.4 mm) flame retardant miltboard covered with not
tess than No. 28 MSG sheet steel, 0.015" (0.4 mm)
stainless steel, 0.024" (0.6 mm) aluminum or 0.020"
(0.5 mm) copper.
30" (76.2 cm) rain. clearance between the top of the
cooking platform and the bottom of an unprotected
wood or metal cabinet.