- ページ 6

照明器具 Jandy CPLVLEDP100のPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Jandy CPLVLEDP100 20 ページ。 Watercolors led lights underwater large and small light
Jandy CPLVLEDP100 にも：インストレーション・マニュアル (16 ページ)

ページを印刷する

Page 6

Section 3. Installing Jandy Light

Fixture during New

Construction

WARNING

Risk of Electrical Shock or Electrocution.

This underwater light must be installed by a licensed

or certified electrician or a qualified pool serviceman

in accordance with the National Electrical Code and

all applicable local codes and ordinances. Improper

installation will create an electrical hazard, which

could result in death or serious injury to pool or spa

users, installers or others due to electrical shock,

and may also cause damage to property.

Always disconnect the power to the color light at the

circuit breaker before installing or servicing the light.

Failure to do so could result in death or serious injury

to serviceman, pool or spa users or others due to

electrical shock.

3.1

Preparing the Light Fixture for

Installation

NOTE The electrician must complete preparatory

steps before light fixture is installed. See

Figure 1.

Ensure that the pool meets the requirements of the

current National Electrical Code and all local codes

and ordinances. A licensed or certiﬁ ed electrician must

install the electrical system to meet or exceed those

requirements before the underwater light is installed.

Some of the requirements of the National Electrical

Code, which the pool electrical systems must meet, are

as follows:

The lighting circuit must have a Ground Fault

Circuit Interrupter (GFCI) for 120 volt models,

and must have an appropriately rated circuit

breaker.

The junction box (or, for 12 volt models, the low

voltage transformer) must be located at least eight

(8) inches above water level, at least four (4)

inches above ground level, and at least four (4)

feet from the edge of the pool; see Figure 1.

The light ﬁ xture and all metal items within ﬁ ve

(5) feet of the pool must be properly electrically

bonded to a reliable point of grounding.

The wet niche must be properly installed so that

the top edge of the underwater light's lens is at

least 18 inches below the surface of the water in

the pool; see Figure 1.

The wet niche must be properly electrically

bonded and grounded via the No. 8 AWG ground

connector located at the rear of the niche; see

Figure 1.

NOTE To be certain that the pool's electrical system

meets all applicable requirements, the

electrician should also consult the local building

department.

Use only approved wet niches (see following note) to

ensure a safe and proper installation.

NOTE Jandy lights are ETL listed (ETL report/file

3141154CHI) for installation with only the

following manufacturer's wet niche fixtures:

Large Niche Model Numbers:

Jandy: PLNICLRG, PLNICVFLRG,

SSNICLRG1R, SSNICLRG1S

Pentair: 620004, 78210200 thru 700,

78210401, 79206700

Hayward DuraNiche: SP0600U

Sta-Rite: 05161-2352 thru 2369, 05163-2395

thru 2396

Small Niche Model Numbers:

Jandy: PLNICSM, SSNICSM,

Pentair: 78241100, 78242200, 78242300

78243100 thru 300, 78244100 thru 300,

79206600

Hayward DuraNiche: SP0601U

Sta-Rite: 05166-1017 thru 1034, 05167-1035

thru 1037

Pentair

® ®

and Sta-Rite

® ®

are registered trademarks of Pentair, Inc.

Hayward

is a registered trademark and DuraNiche

® ®

of Hayward Pool Products, Inc.

To GFCI, Circuit

Breaker and

Power Source.

48"

min.

4" min.

Rigid

Conduit

#8 AWG Ground

Connector bonding

is located at rear

of niche.

Figure 1. Jandy Digital Color Light Installation

is a trademark

™ ™

8" min. Junction Box or Low

Voltage Transformer, to the

max water level of the pool.

18" min. to top of Lens.

Concrete must be cut

back around Niche to

allow for a compacted

plaster seal.

11.50"

Coil 4 ft. of light cable

around Fixture.

16"