- ページ 2
屋外噴水 Garden Treasures F30275ABのPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。Garden Treasures F30275AB 3 ページ。 Lion head fountain
ページを印刷するEstimated time for assembly is 15 minutes.
Tools required for assembly:
•
Screwdriver (not included)
Assembly Instructions
1.
Unpack the contents of the box and check to make sure that all items are accounted for and in good
condition.
2.
Select a flat, level surface for the assembly and final location of your fountain.
3.
Place the basin flat on a horizontal ground. Fill the basin with clean water. The water level should be
approximately 30 mm below the top edge of the basin. (Fig.1)
4.
Insert the water supply tube extending from the underside of the top fountain into the outlet on the pump.
Then place the top fountain onto the basin securely and levelly. And place the pump to the pump
chamber (NOTE: Route the pump power cord from the cord slot on the bottom of Top fountain). Align
the holes on the top fountain with the holes on the basin and secure using screws and washers. Insert
the tongue upwards and Attach the trap door over front of the pump chamber. (Fig.2)
5.
Plug the power cord from the pump into the Ground Fault Circuit Interrupter (GFCI) outlet. Turn the
power source on. The product will start to function as intended. (Fig.3)
6.
To eliminate the possibility of water damage to areas around your fountain, check for leaks and
excessive splashing after the initial setup of your fountain. It is highly recommended that this fountain be
placed in an area that will not be damaged should the area come in contact with liquid.
7.
Do not leave your fountain running for extended periods of time when no one is present to observe the
performance.
8.
Check the area around your fountain on a regular basis to ensure that there is no leakage.
Pump Maintenance Instructions
•
Regular cleaning of the pump is necessary.
•
Keep water clean to prolong the life of pump.
•
Clean pump when it is dirty or when a drop in performance is detected. Use warm, soapy water and a
stiff brush for heavily stained surfaces. Do NOT use harsh chemicals, as this will damage the surface
finish.
•
Failure to clean the pump will result in overheating and voiding of the warranty.
•
Use a filter on pump if available.
•
Disconnect the power and empty the reservoir if the fountain will not be used for an extended time.
•
Do NOT operate fountain in temperatures below 41°F (5°C). Freeze damage may occur. If the fountain
is kept outdoors in freezing temperatures, make sure all water is removed and the unit is completely dry.
To disassemble pump for cleaning:
1.
Always disconnect pump from the power source before cleaning.
2.
Remove the inlet screen and impeller housing.
3.
Remove the impeller/rotor assembly by gently pulling on the impeller blades.
4.
Use a soft cloth or brush to clean the impeller/rotor assembly area inside the pump.
5.
Clean the inlet screen, impeller housing and impeller with warm, soapy water.
6.
Reassemble the pump and check for proper operation.
Hints and Troubleshooting
•
If the pump operates but there is no flow, check to make sure that the pump is fully submerged.
•
If the pump operates but there is no flow, check the supply tubing for kinks and correct.
•
If the pump operates but there is no flow, and if the pump is submerged and there are no kinks in the supply tubing, lift the pump out of the water.
Remove supply tubing at pump outlet and clean tubing inside and out if necessary. Put pump back into water (outlet side up). Once water begins to
flow, reattach the supply tubing.
Pump is replaceable with model # PT-505 UL. Call Customer Service at 866-728-6187 for replacement parts.
SAVE THESE INSTRUCTIONS!
Note: Each Garden Treasures fountain product may have variations in texture, finish and appearance from unit to unit. This enhances the beauty of the
product and makes each Garden Treasures fountain product unique. Some products and finishes are intentionally weathered or worn in appearance for
aesthetic design.
1- Year Limited Warranty
(Valid in USA and Canada only)
2