- ページ 4

芝刈り機 Gardena 370 SMのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Gardena 370 SM 6 ページ。 Hand lawn mower

ページを印刷する

Take special care when moving backwards and when pulling the

lawn mower. Danger of stumbling !

Never place your hands or feet on or under moving parts.

If you come into contact

If the cutting tools or the lawn mower should run into an obstruc-

with an obstruction

tion and / or solid objects, the lawn mower should be properly

during mowing :

and thoroughly inspected.

Pay attention to the

Only work when visibility is good.

working environment

3. Assembly

The rod yoke is mounted with the bolts supplied. The rod on the

Assembling the rod yoke

(Fig. A) :

left side

This can only be performed when the yoke is in the vertical posi-

tion, since the groove in the bore hole and the safety peg have

to fit exactly.

On the right aide

and over the second rod bolt by applying slight pressure.

4. Operation

How to cut correctly

The GARDENA Hand Lawn Mower is able to mow grass up to

14 cm length.

However, if the lawn is supposed to be well kept, the grass should

always be kept shorter.

At the beginning of the cutting phase and on newly laid lawns, a

relatively high cutting height should be chosen. With subsequent

cuts, the height should be made gradually lower. In order to obtain

a well-kept lawn, the cutting height should be adjusted to approx.

2 cm.

Try to cut your grass weekly, if possible. A cropped blade of grass

grows well when cut frequently.

Only cut the grass when It Is relatively dry.

In order to obtain a clean cut, push the mower in tracks as straight

as possible at walking speed. The cutting tracks should always

overlap by several centimetres with this so that a grass strip is not

left behind.

Adjusting the cutting height

For this, position the lawn mower on solid, level ground.

(Fig. B, C) :

v Stand behind the lawn mower so that you can put a foot on the

roller

v Loosen both set-screws

ting height with both hands using the adjusting depressions

(Fig. C).

Highest cut :40 mm

Lowest cut : 20 mm

v Make sure that the cutting height markers

cutting height on the scales on both sides.

Now the two set-screws

The mower may only be adjusted to a depth in which the lower

blade does not touch the ground when it is uneven.

with the bore hole Is pushed over the rod bolt.

, the yoke borehole is pushed downwards

(Fig. B / C).

. Now you can adjust the desired cut-

Indicate the same

should be tightened again.

Mowing with a

grass catcher (Fig. F)

5. Maintenance

Adjusting the cutting gear

(Fig. D) :

Cutting test with

newspaper (Fig. E) :

Sharpening of the blades /

Repairs

6. Storage

With the use of the GARDENA Grass Catcher, Art. No. 2491,

you save yourself the trouble of raking up the mowed grass.

Good grass catching results can be obtained by cutting the grass

when it is dry and pushing the mower at a fast walking speed.

Clean the mower after use and lubricate with an oil of low viscosity

(e.g. spray-oil). Grease the cutting blades.

The cutting gear of your lawn mower was optimally adjusted be-

fore leaving our company. If, after longer use, a clean cut of the

grass is no longer possible or the blade roller contacts the lower

blade, then the lower blade should be adjusted as follows:

v Push the supplied thickness gauge

on the left side between

a blade of the blade roller and the tower blade.

v Turn the hexagonal bolt

to the right using a 10 mm fork

wrench until the thickness gauge is slightly contacted.

v Repeat this procedure on the right side of the mower.

v Now turn the blade roller as a test; it should not touch any of

the five cutters on the lower blade.

Handling the cutting gear should be carried out with special

care (danger of Injury by cutting).

After you have adjusted the cutting gear, carry out a cutting test

with newspaper.

If you take proper care of the cutting blade it will remain sharp for

many years. When it comes time to change the blade, however,

please contact GARDENA Customer Service.

Repairs of the lawn mower and installation of the blades can be

carried out by a suitable workshop.

Have your lawn mower checked in autumn, if possible, so that it is

immediately ready for use for the next mowing season.

For safety reasons, only use original GARDENA spare parts or

parts approved of by the manufacturer.

Store the mower in a dry room. Lubricate with machine oil.