- ページ 5

水ポンプ Gardena 1436のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Gardena 1436 10 ページ。 Petrol-driven motor pump
Gardena 1436 にも：取扱説明書 (17 ページ), 取扱説明書 (11 ページ), 取扱説明書 (11 ページ)

ページを印刷する

Cleaning / adjusting

The spark plug must be free of combustion residues to

the spark plug:

ensure that the motor functions correctly. Only spark plugs

of type Champion RZ7C or equivalent may be used.

1. Unplug the spark plug connector

2. Unscrew the spark plug

plug spanner provided.

3. Clean the spark plug

adjust the electrode gap to 0.6 - 0.7 mm by

bending the electrode

4. Check sealing washer

5. Screw in the spark plug

hand.

6. Tighten the spark plug

spanner:

– 1/2 a turn for a new spark plug

– 1/4 to 1/8 of a turn for an old spark plug.

7. Insert spark plug connector

Replace petrol filter:

The petrol filter must be replaced after one year or

every 300 operating hours.

1. Unscrew petrol cap

2. Pull petrol filter out of petrol tank

a wire).

3. Remove petrol filter

4. Push new petrol filter

5. Screw petrol cap

Rinsing / cleaning the pump:

Clear water should be used for rinsing.

1. After pumping chlorinated swimming pool water, rinse the

pump with warm water (max. 35 °C).

2. Remove deposits and foreign bodies in the cooling ribs

with a soft brush.

Maintenance work is not covered by the guarantee.

You may be charged for maintenance work performed by

GARDENA.

7. Trouble-Shooting

v Before eliminating faults, switch the motor off and allow

to cool down. Then remove the spark plug connector

(see "Clean spark plug").

using the spark

and if necessary

on the spark plug

all the way in by

using the spark plug

(e.g. with the hook of

from petrol hose

onto petrol hose

on again.

Cleaning the turbine:

If the turbine clogs it must be cleaned.

1. Unscrew the 6 Allen screws

Allen key (size 10).

2. Remove housing cover

3. Clean the turbine.

4. Mount the housing cover

Disassembly of the hydraulic unit other than removing

the housing cover must only be carried out by GARDENA

Service.

Problem

Possible Cause

The motor does not start.

The ignition switch

set to position "I".

The fuel tank is empty.

The spark plug is defective.

Motor cold and choke lever not

in Start position.

Motor warm and choke lever

not in Run position.

The pump does not pump

The pump was not filled with

the liquid.

the liquid to be pumped

before it was switched on.

Pressure hose not fixed

1 – 2 m high.

Suction hose defective or

leaking.

Housing cover

turbine clogged.

The pump motor runs but the

Suction filter on suction hose is

delivery capacity or the

sucked clear.

pressure suddenly decreases.

Suction filter of the suction

hose is blocked.

Air cannot escape during

self-priming because the

delivery side is closed or

there is residual water in the

delivery hose.

Suction head too high.

of the housing cover

with an

in the reverse order.

Remedy

is not

v Set the ignition switch

to "I".

v Pour petrol into the fuel tank

(see 6. Maintenance).

v Check the spark plug

and install a new spark

plug if necessary

(see 6. Maintenance).

v Set choke lever to

Start position.

v Set choke lever to

Run position.

v Fill the pump

(see 4. Operation).

v Fix pressure hose 1 – 2 m

high.

v Fit a new suction hose.

soiled or

v Clean the turbine.

v Reduce the flow rate at the

delivery side with a regu-

lator valve, e.g. GARDENA

Regulator Valve Art. (2)977.

v Clean suction filter.

v Open shut-off device

(e. g. water stop) in the

pressure line or drain

the delivery hose.

v Reduce suction head

(see 9. Technical Data).