- ページ 8

水ポンプ Gardena 2000/2 Clear 18V P4AのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Gardena 2000/2 Clear 18V P4A 18 ページ。 Battery submersible pump/battery rain water tank pump

ページを印刷する

1. Push the Flow button

(m)

The current power level is displayed for 5 seconds.

2. Push the Flow button

(m)

edly until the desired power level is displayed.

Depending on environmental conditions (e. g. direct sun-

light), the pump can activate the overheating protection.

A short cooling phase may then be necessary before

restarting.

Timer-Function:

With the timer function the pump can be switched off auto-

matically after 5, 10 or 15 minutes.

Displays when selecting the timer time:

(L1)

flashes green and blue alternately

(L1)

(L2)

and

flashes green and blue

alternately

(L1)

(L2)

(L3)

and

flashes green and blue

alternately

1. Push and hold the Flow button

LED

(L1)

flashes green and blue alternately.

(m)

2. Push the Flow button

edly until the desired timer time is displayed.

If no button is pressed for 5 seconds, the timer func-

tion will start. The pump runs according to the selected

timer time and then switches off automatically.

Displays after starting the timer function:

Timer-Time

15 min.

10 min.

Approx.

15 – 10 min.

10 – 7 min.

Approx.

10 – 5 min.

7 – 3 min.

Approx.

5 – 0 min.

3 – 0 min.

For the last 5 seconds the blue LED

After starting the timer function, first the timer time is dis-

played 5 times in blue LEDs and then 1 time the battery

charge status in green LEDs for one second.

Notes:

The timer function can be cancelled at any time by

pressing the On / Off button.

If the battery runs out during the timer function, the pump

switches off early.

Applications:

CAUTION! Destruction of the battery!

The battery unit is destroyed when they are

immersed in water.

v Do not immerse the battery unit in the water.

Observe the minimum water level (see 7. TECHNICAL

DATA).

on the control panel.

on the control panel repeat-

Timer to 5 minutes

Timer to 10 minutes

Timer to 15 minutes

(m)

for 3 seconds.

on the control panel repeat-

Timer-Time

Timer display in

5 min.

blue LEDs

(L1)

(L2)

(L3)

Approx.

and

5 – 3 min.

go out sequen-

tially

(L1)

(L2)

Approx.

and

go out

3 – 1 min.

sequentially

(L1)

Approx.

goes out

1 – 0 min.

(L1)

flashes rapidly.

Use in flat containers [ Fig. O5 ]:

Art. 14600: The pump is equipped with a hose connector

which allows high flow rates.

Art. 14602: If the rain water tank pump is placed in flat

containers, e. g. to empty a paddling pool, the telescopic

pipe can be removed and replaced with the 33.3-mm (G1)

GARDENA Tap Connector Art. 18202.

(D)

1. Place the battery unit

water.

2. Place the pump in the container.

3. Start the pump.

Flat suction [ Fig. O6 ]:

In normal operation (with foot

of approx. 25 mm is achieved. With flat suction (without

(9)

foot

) a residual water level of approx. 5 mm is achieved.

(9)

1. Turn the foot

anti-clockwise and remove the foot

(bayonet lock).

2. Make sure that the filter

3. For reassembling the suction foot,

see 4. MAINTENANCE.

The pump must not be operated without the filter

To pump water from container [ Fig. O7 ]:

For Art. 14602: The length of the telescopic pipe

should be adjusted in such a manner that the pump does

not touch the bottom of the container; this way, dirt in the

container is kept away from the pump.

The pump should hang approx. 10 cm above the bottom

of the container to prevent excessive contamination.

1. Open the bracket on the battery container

(D)

2. Hang the battery unit

the container or place it in a suitable, flood-proof place.

3. For Art. 14600: Hang the pump into the container

using a rope (do not hang it with the cable).

For Art. 14602: Hang the pump with the telescopic

(3)

tube

into the container.

4. Start the pump.

To start the pump [ Fig. O1 / O4 ]:

To start:

(8)

1. Open the cover

2. Put the battery

(B)

into the battery holder

audibly engages.

3. Close the cover

(8)

until it engages noticeably.

Make sure that the cover

properly closed.

4. Push the On / Off button

The Pump starts and the battery charge status

indication is displayed.

NOTES:

Depending on the length of the hose and the type

of installation, it may take some time for the pump

to deliver the water.

If the pump does not deliver water after several

suction attempts, there is probably air in the hose.

v Start the pump once briefly in water without

a hose.

in a place protected from

(9)

), a residual water level

(10)

is inserted correctly.

(10)

(3)

(D)

on the outside, on the side of

(D)

until it

(8)

of the battery container is

(s)

(P)

on the control panel

(9)