- ページ 3

水ポンプ Gardena 4000/5のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Gardena 4000/5 10 ページ。 Garden pump
Gardena 4000/5 にも：取扱説明書 (17 ページ), 取扱説明書 (12 ページ), 取扱説明書 (14 ページ), 取扱説明書 (11 ページ), 取扱説明書 (10 ページ), 取扱説明書 (18 ページ), 取扱説明書 (10 ページ), 取扱説明書 (19 ページ), 取扱説明書 (13 ページ), 取扱説明書 (17 ページ)

ページを印刷する

3. Initial Operation

Setting up your Garden Pump:

The site must be firm and solid in order to ensure safe and sturdy

operating conditions for the pump.

v Position the pump at a safe distance (min. 2 m) from the liquid

to be pumped.

The pump must be installed in a location with low air humidity

and sufficient ventilation in the area of the ventilation slots.

It must be at a distance of at least 5 cm from the walls.

No dirtcontamination (e.g. sand or earth) may be sucked in

through theventilation slots.

Connecting hose to

Don't use any hose connection system fittings on the

suction side:

suction side! A vacuum-resistant suction hose must be used,

e. g. GARDENA Suction Unit, art. no. 1411.

In order to reduce the suction time, it is advisable to use a suction

hose with backflow preventer avoiding automatic draining of the

suction hose when the pump is stopped.

1. Screw a vacuum-resistant suction hose

connector on the suction side of the pump

2. For suction heights exceeding 4 m also secure the suction

hose

This relieves the pump of the weight of the suction hose.

Connecting hose to

The pumps have 2 connections

delivery side:

The pump connection not in use has to be closed by the cap

which can be unscrewed for connecting 2 hoses.

The pump connections

thread which can be used to connect 13 mm (1/2"), 16 mm (5/8")

or 19 mm (3/4") hoses via the GARDENA hose connection system.

Optimised use of the pump capacity is achieved by connecting

19 mm (3/4") hoses with e.g. GARDENA Pump Connection Set

Art. 1752, or by connecting 25 mm (1") hoses with GARDENA

Quick Thread Coupling with female thread Art. 7109 / Quick

Coupling Hose Connector Art. 7103.

v Connect the pressure hose

side

If more than 2 hoses / accessories are connected simultaneously,

we recommend using the GARDENA 2- or 4-Channel Water

Distributor Art. 8193/8194, GARDENA Twin-Tap Connector

Art. 940 which can be screwed directly onto the connection

on the delivery side

airtight onto the

(e.g. by fastening it to a wooden post).

on the delivery side.

are equipped with a 33.3 mm (G 1")

to the connector on the delivery

4. Operation

Filling the pump:

DANGER! Electric shock!

Risk of injury due to electric shock.

v Disconnect from the mains before filling the

Garden Pump.

ATTENTION!

v Before each operation, slowly fill the pump with liquid

to be pumped until it overflows (approx. 2 to 3 l).

1. Open the cap

on the filler neck

2. Fill the pump via the filler cap

approx. 2 to 3 l of the liquid to be pumped.

3. Tighten the cap

of the filler cap

4. Open any shut-off valves in the delivery line (accessories,

water stop, etc.).

5. Drain remaining water in pressure hose

escape during the suction process.

6. Switching on pump 4000/5: Lift and hold the delivery hose

at least 1 m vertically above the pump, press the On/Off

switch

(On/Off switch shines) and wait until the pump has

primed.

v If the pump does not deliver after approx. 5 minutes,

switch off the pump (press On/Off switch

(see 7. Trouble-Shooting).

min.

6. Switching on pump 5000/5; 6000/6 inox:

1 m

Lift and hold the delivery hose

1 m vertically above the pump, insert the

power plug, press the On/Off button

(the LED shines green) and wait until the

pump has primed.

If the pump does not deliver within

approx. 20 seconds, the LED flashes

orange.

If the pump does not deliver: 5000/5

within approx. 5 minutes / 6000/6 inox

within approx. 6 minutes, the LED

shines red and the pump switches off

automatically (see "7. Trouble-

Shooting").

v If the pump does not automatically

switch off then manually switch

the pump off and check the hose

for leaks.

The specified maximum self-priming suction height of 8 m is

reached only if the pump is filled via the filler neck

overflow and if, while doing so and during the self-priming, the

delivery hose

is held up sufficiently high to prevent any flow

medium escaping from the pump via the delivery hose

by hand.

to overflowing with

by hand (do not use pliers).

so that air can

)

LED

at least

up to the