- ページ 2

水ポンプ Gardena WP 600のPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Gardena WP 600 6 ページ。 Fountain pump 12 v
Gardena WP 600 にも：取扱説明書 (8 ページ), 取扱説明書 (7 ページ), 操作説明 (8 ページ)

ページを印刷する

GARDENA Garden Spring Pump

WP 600 / WP 1200 / WP 1800

Welcome to the Garden of GARDENA ...

This is the translation of the original German User's Manual.

Please read the User's Manual carefully and comply with them.

Use this User's Manual to familiarise yourself with the pump, its

proper use and the safety instructions.

For safety reasons, children under 16 as well as persons

not familiar with this User's Manual must not use this pump.

v Keep this User's Manual in a safe place.

Contents

1. Where to use your GARDENA Garden Spring Pump. . . . . . . . . 8

2. Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3. Initial Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

4. Storing your Fountain Pump Set . . . . . . . . . . . . . . . . . . . . . . . 10

5. Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

6. Trouble-shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

7. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

8. Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

9. Service / Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

1. Where to use your GARDENA Fountain Pump set

Intended Use:

The GARDENA Garden Spring Pump is intended for domestic use

for supplying water to springs and gargoyles. It is not designed

for operating watering equipment and accessories or irrigation

systems. The pump can be used both indoors and outdoors.

Please note

The GARDENA Garden Spring Pump is not suitable for

continuous operation in industrial applications. Corrosive,

easily combustible, aggressive or explosive substances

(such as gasoline, petroleum or nitro thinners), or saltwater

must not be pumped, nor must foodstuffs or drinking water.

2. Safety instructions

Electrical Safety:

DANGER ! Electric shock !

v Always disconnect the pump

from the mains before under-

taking any work on it.

The pump should be operated via a residual

current device with a residual current rating of

30 mA (DIN VDE 0100-702 and 0100-738). The

pump must be placed on solid, even ground.

v Please ask your electrician for his advice.

Mains power cables should not have a smaller

cross-section than a rubber sheathed cable

of the designation H05 RN-F3G0,75.

Extension cables must meet the requirements

of DIN VDE 0620. Check line voltage.

Data indicated on the type plate must match

technical data of the mains supply.

Please unplug the pump after operation and

before carrying out any maintenance works.

The pump must not be operated when there

are people in the water.

Swimming pools and garden ponds should

be designed according to international and

national design regulations.

v Please consult a professional electrician.

Before operating the pump, look to see if there

is any damage to the pump (esp. regarding

power cable and plug).

The connection cable of the pump cannot be

replaced. If the cable is damaged the pump

must be scrapped.

Do not use the power cable to carry the pump

or to pull the plug out of the socket.

3. Initial Operation

Commissioning the pump:

1. Screw the stepped nipple

2. Connect the stepped nipple

a hose (

3. Install the pump at ground level so that the filter housing

standing in water to at least half its height.

4. Insert the pump plug into a mains socket.

Caution: The pump will start immediately.

5. Use the flow control

spring / gargoyle.

Commissioning the pump if

If the pump is installed out of water, the filter housing

it is installed out of water:

be taken off.

1. Pull off the filter housing

2. Turn the pump inlet

motor housing

3. Depending on the pumping application, the pump inlet can

be rotated in 90° steps. Twist the pump inlet

again press it vertically on to motor housing

clockwise (see 5. Cleaning).

4. Screw stepped nipples

pump outlet

5. Connect the pump inlet

(

⁄

" or

han the pump inlet

6. Connect the pump outlet

hose (

7. Fill the hose to the pump inlet

8. Insert the pump plug into a mains socket.

Caution: The pump will start immediately.

9. Use the flow control

spring.

Protect the power cable from heat, oil and

sharp edges.

User instructions:

Never let the pump run dry; running dry

generates heat and will damage the pump.

The temperature of the liquid used must not

be below 4 °C or above 35 °C.

Sand and other abrasive substances in the

liquid cause increased wear and reduce the

output of the pump.

Please observe the local noise prevention

regulations.

on to the pump outlet

to the spring / gargoyle with

⁄

" or

⁄

").

to set the desired water flow for the

anticlockwise and pull it vertically off the

(bayonet socket).

accordingly,

and tighten it

on to the pump inlet

and

to the water reservoir with a hose

⁄

"). The level in the water reservoir must be highert-

to the spring / gargoyle with a

⁄

" or

⁄

").

with water.

to set the desired water flow for the

must