- ページ 7

トリマー Gardena ComfortCut 550/28のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Gardena ComfortCut 550/28 10 ページ。

ページを印刷する

6. TROUBLESHOOTING

DANGER! Risk of injury!

Cut injury when the product starts accidentally.

v Wait for the cutting filament to stop and disconnect the

product from the mains before you troubleshoot the product.

To replace the filament cassette [ Fig. T1 / T2 / T3 ]:

DANGER! Risk of injury!

Risk of injury from metal cutting parts!

v Do not use metal cutting parts or replacement parts and

accessories not approved by GARDENA.

v Only use original GARDENA Filament Cassettes.

If the wear rib

(29)

is no longer visible, the cassette cover

replaced. Contact the GARDENA Service.

You can order the Replacement Filament Cassettes from your GARDENA

dealer or directly from the GARDENA Customer Service.

• GARDENA Filament Cassette for Trimmers Art. 5307

(21)

1. Push in cassette cover

on the two locking clips

and remove it.

2. Remove the filament cassette

3. Remove all possible dirt of the filament cassette holder

4. Pull approx. 15 cm of the cutting filament

cassette

(23)

through the hole in the plastic ring

5. Put the cutting filament

(18)

through the metal sleeve

6. Put the cutting filament

(18)

around the guide pin

(23)

7. Put the filament cassette

into the filament cassette holder

(21)

8. Attach the cassette cover

on the filament cassette holder

both locking clips audibly engage.

Make sure that the cutting filament is not squeezed.

If the cassette cover

(21)

cannot be attached, turn the filament cassette

back and forth, until the filament cassette

cassette holder

(24)

An additional filament cassette

(23)

carrier

(28)

on the trimmer.

v Push the filament cassette

(23)

onto the filament cassette carrier

it engages.

Problem

Possible Cause

Trimmer does not cut

Cutting filament is worn or too

short.

Filament cassette is empty.

Cutting filament is pulled into

the cassette or welded.

Cutting filament cannot be

Cutting filament became too

extended or is used quickly

dry and brittle (e. g. during the

winter).

Cutting filament frequently

touched hard objects.

Trimmer does not start

Engine is blocked.

Trimmer can no longer be

Start lever is stuck.

stopped

NOTE: For any other malfunctions please contact the GARDENA service depart-

ment. Repairs must only be done by GARDENA service departments or specialist

dealers approved by GARDENA.

7. TECHNICAL DATA

Trimmer

Unit

Rated Power

Mains voltage

V (AC)

Mains frequency

Cutting width

(21)

must be

(22)

at the same time

(23)

(24)

(18)

out of the new filament

(25)

(26)

(27)

(24)

(23)

is completely in the filament

can be attached to the thread spool

Remedy

v Extend the cutting filament

(see 3. OPERATION

To extend the cutting filament

(Tip mechanism) ).

v Replace the filament

cassette.

v Pull the cutting filament out of

the filament cassette.

v Put the filament cassette in

water for approx. 10 hours.

v Prevent the cutting filament

from touching hard objects.

v Remove the obstacle.

Start again.

v Disconnect the trimmer

from the mains and loosen

the start lever.

Value

(Art. 9870)

(Art. 9872)

(Art. 9874)

450

550

650

230

Trimmer

Rpm of filament cassette

Cutting filament supply

Cutting filament feed

Weight

Sound pressure level L

Uncertainty k

Sound power level L

measured/guaranteed

Uncertainty k

Hand/arm vibration a

vhw

Uncertainty k

vhw

Measuring process complying with:

NOTE: The stated vibration emission value has been measured according to

a standardized test procedure and can be used for comparison of one electric

power tool with another. It can also be used for preliminary evaluation of expo-

sure. The vibration emission value can vary during actual use of the electric power tool.

8. ACCESSORIES

GARDENA Filament Cassette

for trimmers

GARDENA Replacement

Cassette Cover

GARDENA Wheel set

for trimmer (only for

Art. 9872 / 9874)

until

9. SERVICE / WARRANTY

(23)

Service:

Please contact the address on the back page.

Warranty statement:

In the event of a warranty claim, no charge is levied to you for the services

(28)

until

provided.

GARDENA Manufacturing GmbH grants a warranty for all original

GARDENA new products for two years from the date of original pur-

chase from the retailer, provided that the devices have been for private

use only. This manufacturer's warranty does not apply to products

acquired second hand.

This warranty includes all significant defects of the product that can be

proved to be material or manufacturing faults.

This warranty is fulfilled by supplying a fully functional replacement product

or by repairing the faulty product sent to us free of charge; we reserve

the right to choose between these options. This service is subject to the

following provisions:

• The product has been used for its intended purpose as per the recom-

mendations in the operating instructions.

• Neither the purchaser nor a third party has attempted to open or repair

the product.

• Only Original GARDENA replacement parts and wear parts have been

used for operation.

• Presentation of the receipt

Normal wear and tear of parts and components (such as blades, blade

fixing parts, turbines, light bulbs, V-belts / toothed belts, impellers, air

filters, spark plugs), visual changes, wear parts and consumables are

excluded from the warranty.

This manufacturer's warranty is limited to replacement and repair of

products in accordance with the abovementioned conditions. The manu-

facturer's warranty does not constitute an entitlement to lodge other

claims against us as a manufacturer, such as for damages. This manu-

facturer's warranty does not, of course, affect statutory and contractual

warranty claims against the dealer / retailer.

The manufacturer's warranty is governed by the law of the Federal

Republic of Germany.

In case of a warranty claim, please return the faulty product, together with

a copy of the receipt and a description of the fault, with postage paid to

the service address.

Consumables:

The filament cassette and the cassette cover are consumables and are not

included in the warranty.

Unit

Value

(Art. 9870)

(Art. 9872)

R/min.

11800

11500

Tip mechanism Tip mechanism Tip mechanism

2.6

2.8

dB (A)

2.5

94 / 95

95 / 96

dB (A)

< 2.5

3.2

m/s

1.5

EN 50636-2-91

RL 2000/14/EC

As replacement for consumed filament cassettes.

Available via the GARDENA Service.

For easy cutting of lawn edges.

Value

(Art. 9874)

11500

3.0

2.5

95 / 96

2.5

1.5

Art. 5307

Art. 9880