- ページ 3

フィットネス機器 Align-Pilates C8-Pro ReformerのPDF 組み立て説明書＆取扱説明書をオンラインで閲覧またはダウンロードできます。Align-Pilates C8-Pro Reformer 12 ページ。

ページを印刷する

2. Assembling the foot bar

a) Carefully cut off the cable ties holding the foot bar in the folded position on top of the

frame.

b) Cut off the cable ties holding the chrome Gear bar (#26 - see exploded

diagram on page 11) and position it in the 3rd slot away from the end of the

reformer.

c) Now insert the M8 x 15mm dome headed bolt from the inside and hand tighten.

See Fig. 2. Repeat on the other side.

d) Now bolt the Foot bar Selector bar to the chrome Gear bar (#26) from the outside

using the M8 20mm bolt (#103) . Repeat on the other side, but do not fully tighten. See

Fig. 1.

e) When all bolts are in go round and fully tighten all four bolts with the provided allen key

Note: at this point if you have only ordered the C8–Pro RC, without the extension legs or

freestanding leg attachments please jump to section 5.

3. Attaching the Leg Extensions* (optional extra)

If you bought the optional leg height extensions now is a good time to attach them. We

recommend you get a pair of stable trestles to put the reformer on to enable easy fitting

of the legs. Ensuring the trestles have something soft on them to avoid scratching the

frame, lift the reformer and place it on to the trestles, so that one trestle is underneath the

point where the foot bar attaches to the runner and the other is near the rope riser end.

Remove the wheel bracket at the foot end of the reformer, placing all nuts, bolts and washers to one side. Store the

parts in the order you removed them and then reinstall the wheels on to the higher legs. Remove all four of the black

adjustable screw in feet by unscrewing them completely out and then screw these completely in to the C8-Pro leg

extensions.

Using the allen bolts and a 6mm Allen key, screw in the 5 bolts per leg and hand tighten. Be careful not to cross

thread the bolts. Once all the bolts are in, tighten fully with the Allen key. After removing your

trestles or other elevation device, put your reformer down where you intend to use it. Then use a spirit level to check

the reformer is level and stable. Adjust the level of the reformer by turning the rubber feet in or out. The parts list and

exploded diagram is shown in Fig. 3 for your reference.

4. Free Standing Legs* (optional extra)

The C8-Pro RC model has the ability to free stand with the addition

a pair of freestanding legs (optional extra), shown in Fig.4, which

bolt on to the frame. To install the legs simply remove the 4 bolts

(#143), position the leg bracket so that the leg can fold inwards,

then thread the bolts back through the frame and leg and hand

tighten. When all 4 bolts are in tighten fully with a 6mm allen key. To

use the legs, remove the safety pin from its storage location, then

stand the reformer, once vertical open both the legs 90 degrees

with your foot and let the reformer free stand. Now

reinsert the safety pin to lock the legs open. To lower remove

the safety pin, then whilst supporting the reformer, take the

pressure off the legs and fold them in with your foot then lower the

reformer carefully down. Note: When standing the reformer always

make sure the spring bar is in the position closest to the standing

platform before lifting.

*Both the leg extensions & freestanding legs packages include a new Safety sticker. Please stick this on to the reformer

frame between the rope risers, such that is readable when standing ready to lift the reformer.

Ref

Name

Right* leg foot bar end

Left* leg foot bar end

Left* leg rope riser end

Right* leg rope riser end

Flat washer

Spring washer

Nickel plated Allen Bolt

* Leg positions as it standing at foot bar end looking toward rope risers

Fig.1

Fig.2

Specification

Qty

8.5*20*T1.5

8.3*12.7*T2.0

M8*20

Fig.3

Fig.4