- ページ 27

カーナビゲーションシステム Garmin VIEO RV 851のPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Garmin VIEO RV 851 38 ページ。
Garmin VIEO RV 851 にも：クイック・スタート・マニュアル (25 ページ)

ページを印刷する

Disabling a Zone

You can disable an unused zone and remove it from the audio

level pages. When a zone is disabled, you cannot change any of

the settings for that zone. You can disable zones 2, 3, and 4

only.

Select

Select a zone.

Select ZONE ENABLED to clear the check box.

Disabling the Internal Amplifiers

If you do not connect speakers directly to zones 1 and 2, you

can disable the internal amplifiers to reduce power consumption.

Select

Select INTERNAL AMP ON to clear the check box.

Network Configuration

TIP: You can select the network status icon from any screen to

open the network configuration menu.

Setting the Fusion PartyBus Device as the DHCP Server

If you connected two Fusion PartyBus devices together directly,

or connected more than two together using a network switch or

wireless access point and did not install a router, you must

configure only one Fusion PartyBus stereo to be the DHCP

server.

Select

ETHERNET IP > STATIC IP > SAVE.

Select

SERVER > DHCP ENABLED > SAVE.

You can configure the IP address range of the DHCP server

(DHCP Settings, page

21).

Setting the Fusion PartyBus Device as a Wireless Access

Point

Before you can connect additional Fusion PartyBus devices or

smartphones to a Fusion PartyBus device wirelessly, you must

configure at least one device as a wireless access point. This is

not necessary if you installed a wireless router or other wireless

access point on the network.

Select

POINT.

Select SSID, and change the default SSID, or name, for the

wireless access point (optional).

Select AP SECURITY, and change the security type for the

access point (optional).

NOTE: It is strongly recommended that you use the default

WPA2 PERSONAL AP SECURITY setting. It is the most

widely-used and secure wireless security protocol.

Select PASSWORD, and change the default password for

the access point (optional).

If necessary, select COUNTRY, and select your region.

Select CHANNEL, and select a channel range for the access

point (optional).

Select SAVE.

You can adjust the wireless access point configuration at any

time

(Wireless Access Point Settings, page

Connecting the Fusion PartyBus Device to a Wireless

Access Point

Select

SSID.

A list of wireless access points within rage appears.

Select the Fusion PartyBus wireless access point.

Select an option:

• To enter the password, select PASSWORD, enter the

password, and select

Music Playback

> ZONE.

> NETWORK > ADVANCED >

> NETWORK > ADVANCED > DHCP

> NETWORK > WI-FI ACCESS

21).

> NETWORK > WI-FI CLIENT >

• If you are connecting to the wireless access point using

WPS, verify that WPS has been enabled on the access

point, and select WPS.

NOTE: It can take up to two minutes to successfully

connect to the access point after you select WPS.

Select SAVE.

Advanced Network Configuration

You can perform advanced networking tasks on a Fusion

PartyBus device, such as defining DHCP ranges and setting

static IP addresses.

Wireless Access Point Settings

Select

> NETWORK > ADVANCED > WI-FI

ACCESS POINT.

NOTE: You must configure the device to be a wireless access

point before you can change the settings

PartyBus Device as a Wireless Access Point, page

SSID: Sets the SSID, or name, for the network.

AP SECURITY: Sets the type of wireless security protocol used

by the access point.

NOTE: It is strongly recommended that you set the AP

SECURITY using WPA2 PERSONAL. It is the most widely-

used and secure wireless security protocol.

PASSWORD: Sets the password for the access point. This is

not available when the AP SECURITY setting is set to

NONE.

COUNTRY: Sets the region where the stereo is located.

Different regions may use different channels on the wireless

spectrum, so you should set this to best accommodate local

wireless devices.

CHANNEL: Sets the access point to use a group of channels in

the high, low, or middle range of the available spectrum for

your region. You may experience better performance if you

set the channel in a range with fewer broadcasting access

points.

DHCP SERVER: Sets the device to act as a wireless access

point and the DHCP server on the network

page

21).

WPS: Initiates a Wi‑Fi Protected Setup (WPS) connection.

Devices with a WPS button or setting can connect to the

access point on this stereo when the WPS connection is

active.

NOTE: It can take up to two minutes to successfully connect

to the access point after you select WPS.

DHCP Settings

Select

> NETWORK > ADVANCED > DHCP

SERVER.

DHCP ENABLED: Sets the device as the DHCP server on the

network.

START IP: Sets the first IP address in the IP-address range of

the DHCP server.

END IP: Sets the final IP address in the IP-address range of the

DHCP server.

Setting a Static IP Address

If the stereo is configured as a DHCP server, it is automatically

assigned the IP address of 192.168.0.1. You can change this IP

address.

If the stereo is a client on the network and you do not want the

DHCP server to automatically assign an IP address to the

stereo, you can set a static IP address.

NOTE: Every device on the network must have a unique IP

address. If you select a static IP address that is the same as the

IP address on the network, the devices will not work properly.

Select

IP > STATIC IP.

(Setting the Fusion

21).

(DHCP Settings,

> NETWORK > ADVANCED > WI-FI