- ページ 27

船舶用GPSシステム Garmin ECHOMAP 70 SeriesのPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Garmin ECHOMAP 70 Series 50 ページ。 Flat-mount kit
Garmin ECHOMAP 70 Series にも：クイック・スタート・マニュアル (4 ページ), オーナーズマニュアル (38 ページ), オーナーズマニュアル (44 ページ), オーナーズマニュアル (30 ページ), 取付説明書 (6 ページ), オーナーズマニュアル (50 ページ), インストレーション・インストラクション (4 ページ), インストレーション・インストラクション (4 ページ), 取付説明書 (34 ページ)

ページを印刷する

Open the sonar view for which you will change the source.

Select MENU > Sonar Setup > Source.

Select the source for this sonar view.

Renaming a Sonar Source

You can rename a sonar source to easily identify that source.

For example, you use "Bow" as the name of the transducer on

the bow of your boat.

The source is renamed for the present view only. For example,

to rename the Garmin ClearVü sonar source, you must open the

Garmin ClearVü sonar view.

From the sonar view, select MENU > Sonar Setup > Source

> Rename Sonar Sources.

Enter the name.

Adjusting the Level of Detail

You can control the level of detail and noise shown on the sonar

screen either by adjusting the gain for traditional transducers or

by adjusting the brightness for Garmin ClearVü transducers.

If you want to see the highest intensity signal returns on the

screen, you can lower the gain or brightness to remove lower

intensity returns and noise. If you want to see all return

information, you can increase the gain or brightness to see more

information on the screen. This also increases noise, and can

make it more difficult to recognize actual returns.

From a sonar view, select MENU.

Select Gain or Brightness.

Select an option:

• To increase or decrease the gain or brightness manually,

select Up or Down.

• To allow the chartplotter to adjust the gain or brightness

automatically, select an automatic option.

Adjusting the Color Intensity

You can adjust the intensity of colors and highlight areas of

interest on the sonar screen by adjusting the color gain for

traditional transducers or the contrast for Garmin ClearVü and

SideVü/ClearVü transducers. This setting works best after you

have adjusted the level of detail shown on the screen using the

gain or brightness settings.

If you want to highlight smaller fish targets or create a higher

intensity display of a target, you can increase the color gain or

contrast setting. This causes a loss in the differentiation of the

high intensity returns at the bottom. If you want to reduce the

intensity of the return, you can reduce the color gain or contrast.

From a sonar view, select MENU.

Select an option:

• While in the Garmin ClearVü or SideVü sonar view, select

Contrast.

• While in a Panoptix LiveVü sonar view, select Color Gain.

• While in another sonar view, select Sonar Setup >

Advanced > Color Gain.

Select an option:

• To increase or decrease the color intensity manually,

select Up or Down.

• To use the default setting, select Default.

Sonar Recordings

Recording the Sonar Display

NOTE: Not all models support sonar recording.

Insert a memory card into the card slot.

From a sonar view, select MENU > Sonar Setup > Sonar

Recording > Record Sonar.

Sonar Fishfinder

15 minutes of sonar recording uses approximately 200 MB of

space of the inserted memory card. You can record sonar

until the card reaches capacity.

Stopping the Sonar Recording

Before you can stop recording sonar, you must begin recording

(Recording the Sonar Display, page

From a sonar view, select MENU > Sonar Setup > Sonar

Recording > Stop Recording.

Deleting a Sonar Recording

Insert a memory card into the card slot.

From a sonar view, select MENU > Sonar Setup > Sonar

Recordings > View Recordings.

Select a recording.

Select Delete.

Playing Sonar Recordings

Before you can play back the sonar recordings, you must

download and install the HomePort

sonar data onto a memory card.

Remove the memory card from the device.

Insert the memory card into a card reader attached to a

computer.

Open the HomePort application.

Select a sonar recording from your device list.

Right-click the sonar recording in the lower pane.

Select Playback.

Traditional, Garmin ClearVü, and SideVü

Sonar Setup

NOTE: Not all options and settings apply to all models, sounder

modules, and transducers.

From a sonar view, select MENU > Sonar Setup.

Depth Line: Shows a quick-reference depth line.

Scroll Speed: Sets the rate at which the sonar scrolls from right

to left.

In shallow water you might want to slow the scroll speed to

extend the length of time the information is displayed on

screen. In deeper water you can increase the scroll speed.

On-screen Control: Sets the behavior of the buttons on the

sonar screen control. This is available for touchscreen

devices.

Range Lines: Shows the vertical lines indicating the distance to

the right and left of the boat. This setting is available for

SideVü sonar view.

Color Scheme: Sets the color scheme of the sonar view. This

setting might be available in the Appearance menu.

The high contrast color schemes provide darker color

assignments to the low intensity returns. The low contrast

color schemes provide color assignments to the low intensity

returns that are similar to the background color.

Appearance: See

Sonar Appearance Settings, page

Overlay Numbers: Sets the data shown on the sonar screen.

Advanced: See

Advanced Sonar Settings, page

Installation: Restores the default sonar settings.

Setting the Zoom Level on the Sonar Screen

From a sonar view, select MENU > Zoom.

Select an option:

• To zoom in on the sonar data from the bottom depth,

select Bottom Lock.

• To set the depth range of the magnified area manually,

select Manual, select View Up or View Down to set the

21).

™

application and record

22.