- ページ 8
船舶用GPSシステム Garmin GNS 530WのPDF クイック・リファレンスをオンラインで閲覧またはダウンロードできます。Garmin GNS 530W 23 ページ。 For continued airworthiness bell 206b
Garmin GNS 530W にも： パイロット・マニュアル補遺 (24 ページ), パイロット・マニュアル補遺 (50 ページ), パイロット・マニュアル補遺 (50 ページ), パイロット・マニュアル補遺 (24 ページ), 補足マニュアル (12 ページ), クイック・リファレンス (25 ページ), 取扱説明書 (23 ページ)
ページを印刷する
SCREEN LAYOUT/CURSORS/FREQ SELECTION/DATA ENTRY
Screen Layout (windows)
The display is divided into four separate "windows" (or
screen areas). In the GNS 530W, the left 1/4 of the display pro-
vides a COM window (top two lines), a VLOC window, a select-
able window (by default with VOR ident/radial, but selectable
for other data), and a three line annunciator window. The right
3/4 of the display consists of a GPS window, which is where
you'll find the various navigation, waypoint information and
settings "pages". The three lines in the bottom left window of
the display are used for terrain, flight phase, and GPS integrity
annunciators.
COM Window
VLOC Window
VLOC Ident Window
(user-selectable; can also
display traffic or other data)
Terrain Annunciator
Flight Phase Annunciator
GPS Integrity Annunciator
Each unique screen of information is referred to as a "page."
Pages are typically selected using the small and large right
knobs—with the cursor removed from the GPS window.
Cursors
There are two separate cursors: a tuning cursor and a GPS
window cursor. The tuning cursor is used to select the standby
COM or VLOC frequency. Pushing the small left knob moves
the tuning cursor back-and-forth between the COM and VLOC
frequency windows. To set a new active frequency, you must
first enter the frequency in the standby field, then use the COM
or VLOC flip-flop key to activate the new frequency. Push in
on the small right knob and then turn the large right knob to
move the GPS window cursor around the page.
6
Active Frequency on top & Standby
on bottom (highlighted by cursor)
Window
Frequency Selection (530W only)
1.
If the tuning cursor is not currently in
the desired window (COM or VLOC),
press the small left knob momentarily
to switch the highlight between the
COM and VLOC windows. Adjusting
the frequencies with the large and
small left knobs will affect the standby
frequency.
Turn the large left knob to select the
2.
desired megahertz (MHz) value. For
example, the "117" portion of the fre-
quency "117.70".
Turn the small left knob to select the
3.
desired kilohertz (kHz) value. For exam-
ple, the ".70" portion of the frequency
"117.70".
4.
To activate the selected frequency, press
the appropriate flip-flop key—COM for communication
frequencies or VLOC for VOR/Localizer frequencies.
GPS
To Quickly Tune and Activate the 121.500 Emer-
gency Channel
1.
In the GNS 530W, press and hold the COM flip-
flop key for approximately two seconds.
Data Entry
Data is entered in the
GPS window using the
small and large right
knobs. The large right knob
is used to move the cursor
between fields. The small
right knob is used to select
individual characters at the
highlighted cursor location.
For example, to change the
"N" in the illustration at
right to a different character,
turn the small right knob.