- ページ 3
ヒーター Alke Global-5-SEIのPDF インストール、サービス、ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Alke Global-5-SEI 18 ページ。 Atmospheric stainless-steel gas infrared heaters for use in well ventilated areas
ページを印刷するT:
equipped with an independent manual thermostat with remote sensor (Ti = integrated sensor)
S:
equipped with an individual solenoid valve
Ei:
equipped with an electronic ignition device (EID2G)
Ha:
adjusted for high altitude installation (>1400 meter)
Packaging
Normally (depending model and order quantity) the heaters are packed per 1, 2 or 4 in a box. Always
check the heaters for transport damage directly after receiving them. Note that the heaters will be a bit
discoloured by temperature due to a 5 minutes quality check after manufacturing.
The heaters are pre-assembled. In some cases, if there is a risk for damaging during transport, the
thermocouple sensor is separated from the gas safety device. Re-assembly can be simply done by
screwing the M8 nut of the thermocouple sensor (64-68) back on the safety device nut (55) or on EID2G
(59) for the Ei models. Do not tighten too strong.
In most cases the reflector is delivered separately from the burner part to save on transport costs.
Reassembly is easy: move the burner tube through the hole in the reflector. Slide the reflector over the
tube till it rests on the upper plate of the burner. Secure the reflector with 4 nuts M4 (17) and washers
(16).
The thermostat knob is always delivered separated from the thermostat valve.
1) Remove the plastic protection cover from the thermostat valve (sometimes already removed before).
2) Turn the knob on maximum temperature and push the knob on the valve.
3) Fix the knob by turning the large metal screw ring till it stops (at least 2 turns, hand tight).
For thermostats with a remote sensor only: bend the sensor line carefully (no sharp bends) to the
thermostat valve and secure the sensor line with a ty-rap around the red protection lining and the
thermocouple safety device (see picture). Note that the tubing is hollow, a sharp bend will close the
tubing and makes the sensor worthless. The chance of breaking the line at the entrance of the
thermostat knob is largely limited now.
Installation
Before installation, check that the local distribution conditions, nature of gas and pressure, and
adjustment of the appliance are compatible. Make sure that the gas is clean. Install a gas filter and
condensate trap before the heaters in case the gas is dirty or wet/oily. No guarantee can be given on
heaters operating on gas that is not clean.
Dimensions
Physical dimensions of the appliances (rounded values)
Model
Global-5 / Global-10
Global-5-T / Global-10-T
Global-5-2F / Global-10-2F
Global-5-2FT / Global-10-2FT
Global-5-S / Global-10-S
Global-5-2FS / Global-10-2FS
Global-5-Ei / Global-10-Ei
Global-5-2FEi / Global-10-2FEi
Global-5-SEi / Global-10-SEi
Global-5-2FSEi / Global-10-2FSEi
Global-5-2FDi
Version: Sept 2017
Length (cm)
Width (cm)
59 / 69
42 / 61
64 / 74
42 / 61
59 / 69
42 / 61
64 / 74
42 / 61
67 / 77
42 / 61
67 / 77
42 / 61
60 / 70
42 / 61
60 / 70
42 / 61
65 / 75
42 / 61
65 / 75
42 / 61
57
42
3
Height (cm)
Weight (kg)
25 / 25
2,0 / 3,3
31 / 31
2,4 / 3,7
25 / 25
2,2 / 3,5
31 / 31
2,5 / 3,8
26 / 26
2,4 / 3,7
26 / 26
2,5 / 3,8
31 / 31
2,7 / 4,0
31 / 31
2,8 / 4,1
31 / 31
2,9 / 4,2
31 / 31
3,1 / 4,4
25
2,3
manual number: 0009 0440EN