- ページ 8

船舶用GPSシステム Garmin GPSMAP 441のPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Garmin GPSMAP 441 12 ページ。 Marine navigation equipment
Garmin GPSMAP 441 にも：重要な安全情報 (4 ページ), リファレンス・マニュアル (2 ページ), ユーザーマニュアル (28 ページ), テクニカル・リファレンス (42 ページ), 取付説明書 (28 ページ), テンプレートマニュアル (2 ページ), 適合宣言 (1 ページ)

ページを印刷する

Connecting the Wiring Harness to a Garmin CANet Device

If your GPSMAP 400/500 series chartplotter is Garmin CANet-compatible, it can receive sonar information from a CANet-compatible Garmin

Sounder or Fishfinder device. See the chartplotter functionality matrix on

page 1

to determine whether your chartplotter is CANet compatible.

Using the CANet optimizes the performance of CANet-compatible devices, allowing sonar information from a sounder or fishfinder to be

shared with up to two CANet compatible Garmin chartplotters. A standard NMEA 0183 connection only allows depth, temperature, and speed

information to be sent to a single chartplotter, whereas a CANet connection provides full sonar readings, including Ultrascroll

, so you can

™

view and control the same information on your compatible chartplotter(s) as you can on your compatible Garmin sounder or fishfinder.

NOTE: To use the Garmin CANet with your device, you must purchase an optional CANet Kit. Contact your Garmin dealer, or visit

www.garmin.com.

Connecting the Chartplotter to a NMEA 2000 Network

If your GPSMAP 400/500 series chartplotter is NMEA 2000-compatible, you can connect it to an existing NMEA 2000 network on your boat

to share information with other connected NMEA 2000-compatible devices. If you do not have an existing NMEA 2000 network on your boat,

you will need to build one. See

www.garmin.com

for more information.

NOTE: NMEA 2000-compatible GPSMAP 400/500 series chartplotters are not packaged with NMEA 2000 connectors or cables. You will need

a NMEA 2000 T-connector and drop cable to connect it to an existing NMEA 2000 network. NMEA 2000 components are available from your

local Garmin dealer or marine dealer.

NMEA 000-

compatible

GPSMAP

400/500 series

chartplotter

NMEA 000

device

NMEA 000

(not included)

device

(not included)

Drop cable

(not included)

T-connector

(not included)

Existing NMEA 000 network

Connecting a NMEA 2000-compatible GPSMAP 400/500 Series

Chartplotter to an Existing NMEA 2000 Network

To connect a NMEA 2000-compatible GPSMAP 400/500 series chartplotter to your existing NMEA 2000 network:

1. Determine an appropriate location to connect the chartplotter to your existing NMEA 2000 network.

2. Disconnect one side of a NMEA 2000 T-connector from the backbone nearest to the location where you want to connect the chartplotter.

If you need to extend the NMEA 2000 backbone, connect an appropriate NMEA 2000 backbone extension cable (not included) to the side of

the T-connector you disconnected.

3. Add a T-connector (not included) to the NMEA 2000 backbone.

4. Route a NMEA 2000 drop cable from the chartplotter to the top of the T-connector you added to your NMEA 2000 network.

You can use a drop cable up to 20 ft. (6 m). If more cable is needed, add an extension to your NMEA 2000 backbone, based on the

NMEA 2000 guidelines.

GPSMAP 400/500 Series Installation Instructions