- ページ 2

船舶用GPSシステム Garmin GPSMAP 5012 - Marine GPS ReceiverのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Garmin GPSMAP 5012 - Marine GPS Receiver 25 ページ。 Weather and xm satellite radio gpsmap 4000 series; gpsmap 5000 series; gpsmap 6000 series; gpsmap 7000 series
Garmin GPSMAP 5012 - Marine GPS Receiver にも：クイック・リファレンス・マニュアル (2 ページ), オーナーズマニュアル (2 ページ), オーナーズマニュアル (2 ページ), テクニカル・リファレンス (30 ページ), 取付説明書 (19 ページ), 取付説明書 (25 ページ), クイック・リファレンス・マニュアル (2 ページ), 重要な安全情報 (48 ページ), 適合宣言 (1 ページ), 印刷マニュアル (2 ページ), 補足マニュアル (24 ページ)

Mounting the GPSMAP 4000/5000 Series Chartplotter

You can mount the GPSMAP 4000/5000 series chartplotters one of two ways. You can use the included bracket to bail mount the chartplotter, or

you can use the included template and hardware to flush mount the chartplotter.

You cannot bail mount the GPSMAP 5015/5215 chartplotters. Because of the larger size, you must flush mount the GPSMAP 5015/5215 chartplotters.

Bail Mounting the GPSMAP 4000/5000 Series Chartplotter

Use the included bracket to bail mount the GPSMAP 4000/5000 series chartplotter.

tools required (not included):

• Drill and drill bit

• Screwdriver

• Pencil

• Mounting hardware (screws or nuts, washers, and bolts)

NOTE: The mounting hardware (screws or nuts, washers, and bolts) are not included. The holes on the bail mount are 5/16 in. (7.9 mm) in

diameter. Choose mounting hardware that fits the holes in the bail mount and securely attaches it to your specific mounting surface. The size

of the drill bit required depends on the mounting hardware chosen.

to install the bail-mount bracket:

NOTE: You cannot bail mount the GPSMAP 5015/5215 chartplotters. Because of the larger

size, you must flush mount the GPSMAP 5015/5215 chartplotter.

1. Using the bail mount as a template, mark the location of the four mounting holes. Be sure to

leave at least 5 in. (12.7 cm) of clearance behind the 4000/5000 series chartplotter for the

wiring.

NOTE: Mount a GPSMAP 4008/4208/5008/5208 chartplotter 31 1/2 in. (80 cm), and a

GPSMAP 4010/4210/4012/4212/5012/5212 chartplotter 39 3/8 in. (1 m) from a magnetic

compass to avoid interference.

2. Using an appropriately sized drill bit, drill the pilot holes for your mounting hardware.

3. Secure the bail mount to the surface with screws and washers.

to install the GPSMAP 4000/5000 series chartplotter on the bail-

mount bracket:

1. Loosely attach the mounting knobs to the GPSMAP 4000/5000 series

chartplotter.

2. Slide the chartplotter onto the bail mount, and tighten the mounting knobs.

notice

Mounting

screws

Bail-mount

bracket

Mounting knobs ×2

GPSMAP 4000/5000 Series Installation Instructions